該頁無縮略圖
三排牙公制螺紋銑刀-鈦合金/高溫合金-三倍經
特征 Features
■合適加工小孔徑螺紋和硬度比較高的工件、三扣牙剛性好、耐磨性高、螺紋尺寸更加穩定 采用高溫合金、鈦合金專用涂層，提高了刀具的抗粘屑和高溫熔沾問題，從而實現壽命提升
單位UNIT \mathbf { \bar { \rho } } = \mathbf { \rho } MM
| 产品编码 | 尺寸 | 螺距P | 刃径d1 | 避空直径d2 | 避空长L1 | 柄径D | 总长L | 刃数F |
| ISOT0.25 0.730300450 X | M1.0 | 0.25 | 0.73 | 3.0 | 4.0 | 50 | 3 | |
| ISO T0.25 0.920360450 X | M1.2 | 0.25 | 0.92 | 3.6 | 4.0 | 50 | 3 | |
| ISOT0.31.050420450 X | M1.4 | 0.3 | 1.05 | 4.2 | 4.0 | 50 | 3 | |
| ISO T0.351.20480450 X | M1.6 | 0.35 | 1.2 | 4.8 | 4.0 | 50 | 3 | |
| ISOT0.41.550600450X | M2.0 | 0.4 | 1.55 | 6.0 | 4.0 | 50 | 3 | |
| ISOT0.452.00750450 X | M2.5 | 0.45 | 2.0 | 7.5 | 4.0 | 50 | 3 | |
| ISOT0.52.40900450 X | M3.0 | 0.5 | 2.4 | 9.0 | 4.0 | 50 | 3 | |
| ISO T0.73.15120450 X | M4.0 | 0.7 | 3.15 | 12 | 4.0 | 50 | 3 | |
| ISO T0.84.0150450 X | M5.0 | 0.8 | 4.0 | 15 | 4.0 | 50 | 3 | |
| ISO T1.0 4.8180650 X | M6.0 | 1.0 | 4.8 | 18 | 6.0 | 50 | 3 | |
| ISO T1.25 6.0240650 X | M8.0 | 1.25 | 6.0 | 24 | 6.0 | 50 | 4 | |
| ISO T1.5 8.0300860 X | M10 | 1.5 | 8.0 | 30 | 8.0 | 60 | 4 | |
| ISO T1.75 10361075 X | M12 | 1.75 | 10 | 36 | 10 | 75 | 4 |
三排牙公制螺紋銑刀-航空航天專用 Thre Tooth Metric Thread
特征 Features
■合適加工小孔徑螺紋和硬度比較高的工件、三扣牙剛性好、耐磨性高、螺紋尺寸更加穩定 采用高溫合金、鈦合金專用涂層，提高了刀具的抗粘屑和高溫熔沾問題，從而實現壽命提升
單位UNIT \mathbf { \bar { \rho } } = \mathbf { \rho } MM
| 产品编码 | 尺寸 | 螺距P | 刃径d1 | 避空直径d2 | 避空长L1 | 柄径D | 总长L |
| MJT0.41.550600450 X | MJ2.0 | 0.4 | 1.55 | 1.05 | 6.0 | 4.0 | 50 |
| MJT0.452.00750450 X | MJ2.5 | 0.45 | 2.0 | 1.45 | 7.5 | 4.0 | 50 |
| MJT0.52.40900450X | MJ3.0 | 0.5 | 2.4 | 1.8 | 9.0 | 4.0 | 50 |
| MJT0.73.15120450 X | MJ4.0 | 0.7 | 3.15 | 2.3 | 12 | 4.0 | 50 |
| MJ T0.84.0150450 X | MJ5.0 | 0.8 | 4.0 | 3.0 | 15 | 4.0 | 50 |
| MJT1.0 4.8180650 X | MJ6.0 | 1.0 | 4.8 | 3.6 | 18 | 6.0 | 50 |
| MJT1.25 6.0240650 X | MJ8.0 | 1.25 | 6.0 | 4.5 | 24 | 6.0 | 50 |
三排牙公制螺紋銑刀-TiCiN涂層 hre Tooth Meric Thread
特征 Features
■合適加工小孔徑螺紋和硬度比較高的工件，三扣牙鋼性好，強度高，不容易斷
單位UNIT \dot { \bf \Phi } = { \bf \Phi } MM
| 产品编码 | 尺寸 | 螺距P | 刃径d1 | 避空直径d2 | 避空长L1 | 柄径D | 总长L | 刃数F |
| ISOT0.250.730200450 R | M1.0 | 0.25 | 0.73 | 2.0 | 3.0 | 4.0 | 50 | 3 |
| ISOT0.250.920240450 R | M1.2 | 0.25 | 0.92 | 2.4 | 3.6 | 4.0 | 50 | 3 |
| ISO T0.31.050280450 R | M1.4 | 0.3 | 1.05 | 2.8 | 4.2 | 4.0 | 50 | 3 |
| ISO T0.351.20320450 R | M1.6 | 0.35 | 1.2 | 3.2 | 4.8 | 4.0 | 50 | 3 |
| ISO T0.41.550400450 R | M2.0 | 0.4 | 1.55 | 4.0 | 6.0 | 4.0 | 50 | 3 |
| ISOT0.452.00500450 R | M2.5 | 0.45 | 2.0 | 5.0 | 7.5 | 4.0 | 50 | 3 |
| ISO T0.5 2.40600450 R | M3.0 | 0.5 | 2.4 | 6.0 | 9.0 | 4.0 | 50 | 3 |
| ISO T0.73.150800450 R | M4.0 | 0.7 | 3.15 | 8.0 | 12 | 4.0 | 50 | 3 |
| ISO T0.8 4.0100450 R | M5.0 | 0.8 | 4.0 | 10 | 15 | 4.0 | 50 | 3 |
| ISO T1.0 4.8120650 R | M6.0 | 1.0 | 4.8 | 12 | 18 | 6.0 | 50 | 3 |
| ISO T1.25 6.0160650 R | M8.0 | 1.25 | 6.0 | 16 | 24 | 6.0 | 50 | 4 |
| ISO T1.5 8.0200860 R | M10 | 1.5 | 8.0 | 20 | 30 | 8.0 | 60 | 4 |
| ISO T1.75 10241075 R | M12 | 1.75 | 10 | 24 | 36 | 10 | 75 | 4 |
| ISO T2.010281075R | M14 | 2.0 | 10 | 10.1 | 28 | 10 | 75 | 4 |
三排牙公制螺紋銑刀-DIA涂層鋁用
特征 Features
■七彩DLC涂層具有最低的摩擦系數，對非鐵金屬具有高抗熔結性，抗腐蝕性。適合加工銅合金、鋁合金、有色金屬、亞克力等
? 最佳Best O=適合Good
| P | H | K | M | N | S | |||||||||
| 碳素钢合金钢预硬钢 | 淬火钢钢Hardened Steel | 铸铁不锈钢铝合金铜合金 | 塑胶 | 亚克力 高温合金钛合金 | ||||||||||
| Carben | AlloySteel | Prehardened | ~48HRC~55HRC~60HRC | ~65HRC | CastIron | Stainle | Aluminium | Calpe | Peastit | Acrylic | ||||
單位UNIT \mathbf { \bar { \rho } } = \mathbf { \rho } MM
| 产品编码 | 尺寸 | 螺距P | 刃径d1 | 避空直径d2 | 避空长L1 | 柄径D | 总长L | 刃数F |
| ISOT0.25 0.730300450 DLC | M1.0 | 0.25 | 0.73 | 0.43 | 3.0 | 4.0 | 50 | 3 |
| ISOT0.25 0.920360450DLC | M1.2 | 0.25 | 0.92 | 0.62 | 3.6 | 4.0 | 50 | 3 |
| ISO T0.31.050420450 DLC | M1.4 | 0.3 | 1.05 | 0.65 | 4.2 | 4.0 | 50 | 3 |
| ISOT0.351.20480450 DLC | M1.6 | 0.35 | 1.2 | 0.78 | 4.8 | 4.0 | 50 | 3 |
| ISO T0.4 1.550600450 DLC | M2.0 | 0.4 | 1.55 | 1.05 | 6.0 | 4.0 | 50 | 3 |
| ISO T0.452.00750450 DLC | M2.5 | 0.45 | 2.0 | 1.45 | 7.5 | 4.0 | 50 | 3 |
| ISO T0.5 2.40900450 DLC | M3.0 | 0.5 | 2.4 | 1.8 | 9.0 | 4.0 | 50 | 3 |
| ISO T0.73.15120450 DLC | M4.0 | 0.7 | 3.15 | 2.3 | 12 | 4.0 | 50 | 3 |
| ISO T0.8 4.0150450 DLC | M5.0 | 0.8 | 4.0 | 3.0 | 15 | 4.0 | 50 | 3 |
| ISO T1.0 4.8180650 DLC | M6.0 | 1.0 | 4.8 | 3.6 | 18 | 6.0 | 50 | 3 |
| ISO T1.25 6.0240650 DLC | M8.0 | 1.25 | 6.0 | 4.5 | 16 | 6.0 | 50 | 4 |
| ISO T1.5 8.0300860 DLC | M10 | 1.5 | 8.0 | 6.2 | 30 | 8.0 | 60 | 4 |
| ISO T1.7510361075 DLC | M12 | 1.75 | 10 | 7.8 | 36 | 10 | 75 | 4 |
| ISO T2.0 10371075 DLC | M14 | 2.0 | 10 | 7.5 | 28 | 10 | 75 | 4 |
特征 Features
■合適加工小孔徑螺紋和硬度比較高的工件，三扣牙鋼性好，強度高，不容易斷
單位UNIT=MM
| 产品编码 | 尺寸 | 螺距P | 刃径d1 | 避空直径d2 | 避空长L1 | 柄径D | 总长L | 刃数F |
| ISOT0.351.203206100 A | M1.6 | 0.35 | 1.2 | 0.78 | 3.2 | 6.0 | 100 | 3 |
| ISO T0.4 1.5504006100 A | M2.0 | 0.4 | 1.55 | 1.05 | 4.0 | 6.0 | 100 | 3 |
| ISOT0.452.005006100 A | M2.5 | 0.45 | 2.0 | 1.45 | 5.0 | 6.0 | 100 | 3 |
| ISO T0.5 2.400606100 A | M3.0 | 0.5 | 2.4 | 1.8 | 6.0 | 6.0 | 100 | 3 |
| ISO T0.73.150806100 A | M4.0 | 0.7 | 3.15 | 2.3 | 8.0 | 6.0 | 100 | 3 |
| ISO T0.8 4.051006100 A | M5.0 | 0.8 | 4.0 | 3.0 | 10 | 6.0 | 100 | 3 |
| ISO T1.0 4.81206100 A | M6.0 | 1.0 | 4.8 | 3.6 | 12 | 6.0 | 100 | 3 |
| ISO T1.25 6.01606100 A | M8.0 | 1.25 | 6.0 | 4.5 | 16 | 6.0 | 100 | 4 |
| ISOT1.5 8.02008100 A | M10 | 1.5 | 8.0 | 6.2 | 20 | 8.0 | 100 | 4 |
| ISO T1.75 102410100 A | M12 | 1.75 | 10 | 7.8 | 24 | 10 | 100 | 4 |
| ISO T2.0 102810100 A | M14 | 2.0 | 10 | 7.5 | 28 | 10 | 100 | 4 |
特征 Features
■合適加工小孔徑螺紋和硬度比較高的工件，三扣牙鋼性好，強度高，不容易斷
@=最佳Best O=適合Good
單位UNIT=MM
UNF細螺紋
| 产品编码 | 规格 | 刃径d1 | 避空直径d2 | 避空长L1 | 柄径D | 总长L | 刃数F |
| UNFT721.450390450A | NO.1-72 | 1.45 | 1.0 | 3.9 | 4.0 | 50 | 3 |
| UNFT561.950530450 A | NO.3-56 | 1.95 | 1.4 | 5.3 | 4.0 | 50 | 3 |
| UNFT482.250600450A | NO.4-48 | 2.25 | 1.6 | 6.0 | 4.0 | 50 | 3 |
| UNFT402.750720450A | NO.6-40 | 2.75 | 1.9 | 7.2 | 4.0 | 50 | 3 |
| UNFT363.30870450A | NO.8-36 | 3.3 | 2.4 | 8.7 | 4.0 | 50 | 3 |
| UNFT323.9100450A | NO.10-32 | 3.9 | 2.9 | 10 | 4.0 | 50 | 3 |
| UNFT285.3120650A | 1/4-28 | 5.3 | 4.2 | 12 | 6.0 | 50 | 3 |
| UNFT209.5241075A | 7/16-20 | 9.5 | 7.9 | 24 | 10 | 75 | 4 |
UNC粗螺紋
| 规格 | 刃径d1 | 避空直径d2 | 避空长L1 | 柄径D | 总长L | 刃数F | |
| UNCT641.40400450A | NO.1-64 | 1.4 | 0.9 | 4.0 | 4.0 | 50 | 3 |
| UNCT561.650500450 A | NO.2-56 | 1.65 | 1.1 | 5.0 | 4.0 | 50 | 3 |
| UNCT481.950500450A | NO.3-48 | 1.95 | 1.3 | 5.0 | 4.0 | 50 | 3 |
| UNCT402.150600450 A | NO.4-40 | 2.15 | 1.3 | 6.0 | 4.0 | 50 | 3 |
| UNCT402.450720450A | NO.5-40 | 2.45 | 1.6 | 7.2 | 4.0 | 50 | 3 |
| UNCT322.650750450 A | NO.6-32 | 2.65 | 1.6 | 7.5 | 4.0 | 50 | 3 |
| UNCT323.20900450A | NO.8-32 | 3.2 | 2.2 | 9.0 | 4.0 | 50 | 3 |
| UNCT243.7100450A | NO.10-24 | 3.7 | 2.4 | 10 | 4.0 | 50 | 3 |
| UNCT204.9120650A | 1/4-20 | 4.9 | 3.3 | 12 | 6.0 | 50 | 3 |
| UNCT167.8200860A | 5/16-18 | 6.4 | 4.7 | 18 | 8.0 | 60 | 4 |
| UNCT186.4180860A | 3/8-16 | 7.8 | 5.85 | 20 | 8.0 | 60 | 4 |
| UNCT149.2241075A | 7/16-14 | 9.2 | 7.0 | 24 | 10 | 75 | 4 |
| UNCT1310241075A | 1/2-13 | 10 | 7.5 | 24 | 10 | 75 | 4 |
全牙螺紋銑刀加工過程
特征 Features
■合適大批量同規格生產，螺紋規格多，使用方便，2倍徑以內深度的工件，加工效率高
=最佳Best O=適合Good
單位UNIT=MM
| 产品编码 | 尺寸 | 螺距TPI | 刃径d1 | 刃长L1 | 柄径D | 总长L | 刃数F |
| ISOF0.52.4060450D | M3 | 0.5 | 2.4 | 6.0 | 4.0 | 50 | 4 |
| ISO F0.73.15080450 D | M4 | 0.7 | 3.15 | 8.0 | 4.0 | 50 | 4 |
| ISOF0.54.0100450D | M5 | 0.5 | 4.0 | 10 | 4.0 | 50 | 3 |
| ISOF0.754.0100450D | M5 | 0.75 | 4.0 | 10 | 4.0 | 50 | 3 |
| ISOF0.84.0100450D | M5 | 0.8 | 4.0 | 10 | 4.0 | 50 | 4 |
| ISO F0.75 4.8120660 D | M6 | 0.75 | 4.8 | 12 | 6.0 | 60 | 3 |
| ISOF1.04.8120660D | M6 | 1.0 | 4.8 | 12 | 6.0 | 60 | 4 |
| ISO F0.5 6.0160660 D | M8 | 0.5 | 6.0 | 16 | 6.0 | 60 | 3 |
| ISOF0.756.0160660D | M8 | 0.75 | 6.0 | 16 | 6.0 | 60 | 3 |
| ISOF1.0 6.0160660 D | M8 | 1.0 | 6.0 | 16 | 6.0 | 60 | 3 |
| ISOF1.256.0160660 D | M8 | 1.25 | 6.0 | 16 | 6.0 | 60 | 4 |
| ISOF1.08.0200860D | M10 | 1.0 | 8.0 | 20 | 8.0 | 60 | 4 |
| ISOF1.258.0200860D | M10 | 1.25 | 8.0 | 20 | 8.0 | 60 | 4 |
| ISO F1.5 8.0200860 D | M10 | 1.5 | 8.0 | 20 | 8.0 | 60 | 4 |
| ISOF0.510241075D | M12 | 0.5 | 10 | 24 | 10 | 75 | 4 |
| ISO F0.7510241075 D | M12 | 0.75 | 10 | 24 | 10 | 75 | 4 |
| ISO F1.010241075D | M12 | 1.0 | 10 | 24 | 10 | 75 | 4 |
| ISOF1.2510241075D | M12 | 1.25 | 10 | 24 | 10 | 75 | 4 |
| ISO F1.510241075D | M12 | 1.5 | 10 | 24 | 10 | 75 | 4 |
| ISO F1.75 10241075 D | M12 | 1.75 | 10 | 24 | 10 | 75 | 4 |
| ISO F1.012281275D | M14 | 1.0 | 12 | 28 | 12 | 75 | 4 |
| ISO F1.512281275D | M14 | 1.5 | 12 | 28 | 12 | 75 | 4 |
| ISO F2.0 11.6281275 D | M14 | 2.0 | 11.6 | 28 | 12 | 75 | 4 |
| ISOF1.5143214100 D | M16 | 1.5 | 14 | 32 | 14 | 100 | 4 |
| ISOF2.0133214100D | M16 | 2.0 | 13 | 32 | 14 | 100 | 4 |
| ISO F2.5 14.83816100 D | M18 | 2.5 | 14.8 | 38 | 16 | 100 | 4 |
| ISOF1.5163816100D | M20 | 1.5 | 16 | 38 | 16 | 100 | 4 |
| ISOF2.5164216100 D | M20 | 2.5 | 16 | 42 | 16 | 100 | 4 |
| ISO F3.0164216100 D | M24 | 3.0 | 16 | 42 | 16 | 100 | 4 |
特征 Features
■合適大批量同規格生產，螺紋規格多，使用方便，2倍徑以內深度的工件，加工效率高
@=最佳Best O=適合Good
單位UNIT \mathbf { \bar { \rho } } = \mathbf { \rho } MM
| 产品编码 | 粗牙 UNC | 细牙 UNF | 特细牙 UNEF | 牙距 TPI | 刃径 d1 | 刃长 L1 | 柄径 D | 全长 L | 刃数 F |
| UNFF323.9100450D | 10-32 | 32 | 3.9 | 10 | 6.0 | 50 | 4 | ||
| UNEF F32 6.8180860 D | 5/16-32 3/8-32 | 32 | 6.8 | 18 | 8.0 | 60 | 4 | ||
| UNF F285.3120660 D | 1/4-28 | 7/16-28 1/2-28 | 28 | 5.3 | 12 | 6.0 | 60 | 4 | |
| UNF F24 6.5180860 D | 5/16-24 | 9/16-24 5/8-24 | 24 | 6.5 | 18 | 8.0 | 60 | 4 | |
| UNC F204.85120660 D | 1/4-20 | 7/16-20 1/2-20 | 3/4-20 7/8-20 1"-20 | 20 | 4.85 | 12 | 6.0 | 60 | 4 |
| UNF F209.5241075 D | 7/16-201/2-20 | 3/4-207/8-20 1”-20 | 20 | 9.5 | 24 | 10 | 75 | 4 | |
| UNC F186.4180860 D | 5/16-18 | 9/16-18 5/8-18 | 18 | 6.4 | 18 | 8.0 | 60 | 4 | |
| UNF F1810241075D | 9/16-18 5/8-18 | 18 | 10 | 24 | 10 | 75 | 4 | ||
| UNC F167.8210860 D | 3/8-16 | 3/4-16 | 16 | 7.8 | 21 | 8.0 | 60 | 4 | |
| UNF F1612281275D | 3/4-16 | 16 | 12 | 28 | 12 | 75 | 4 | ||
| UNC F148.8241075D | 7/16-14 | 7/8-14 | 14 | 8.8 | 24 | 10 | 75 | 4 | |
| UNC F1310241075D | 1/2-13 | 13 | 10 | 24 | 10 | 75 | 4 | ||
| UNC F12 12281275 D | 9/16-12 | 1"-12 1"-1/8-12 1"-1/4-12 1"-1/2-12 1"-3/8-12 | 12 | 12 | 28 | 12 | 75 | 4 | |
| UNC F1112281275 D | 5/8-11 | 11 | 12 | 28 | 12 | 75 | 4 | ||
| UNCF10163816100 D | 3/4-10 | 10 | 16 | 38 | 16 | 100 | 4 |
BSP(G)55°英制直管螺紋銑刀 BSP(G)55° Inch Pipe Thread Miling Cutter
特征 Features
BSP \left( \mathsf { G } \right) 直管螺紋，加工材料鋁合金，不銹鋼，鈦合金效果很好，效率高
@=最佳Best O=適合Good
| P | H | K | M | N | S | |||||||||
| 碳素钢 | 合金钢 | 预硬钢 | 淬火钢钢Hardened Steel | 铸铁 | 不锈钢铝合金 | 铜合金 | 塑胶 | 亚克力高温合金钛合金 | ||||||
| Carben | AlloySteel | Prehardened | ~48HRC~55HRC~60HRC | ~65HRC | Cast Iron | Stainle | Aluminium | Caloyesr | Cement | Acrylic | ||||
| O | O | |||||||||||||
單位UNIT \mathbf { \bar { \rho } } = \mathbf { \rho } MM
| 产品编码 | 尺寸 | 螺距TPI | 刃径d1 | 刃长L1 | 柄径D | 总长L | 刃数F |
| BSP F28 6.0140660 D | 1/16 | 28 | 6.0 | 14 | 6.0 | 60 | 4 |
| BSP F288.0140860 D | 1/8 | 28 | 8.0 | 14 | 8.0 | 60 | 4 |
| BSPF19 8.0180860D | 1/4 | 19 | 8.0 | 18 | 8.0 | 60 | 4 |
| BSP F19 10201075 D | 1/4 | 19 | 10 | 20 | 10 | 75 | 4 |
| BSP F19 12251275 D | 3/8 | 19 | 12 | 25 | 12 | 75 | 4 |
| BSP F14 12201275 D | 1/2 | 14 | 12 | 20 | 12 | 75 | 4 |
| BSPF1.0163016100D | 3/4 | 14 | 16 | 30 | 16 | 100 | 4 |
| BSP F11163216100 D | 1” | 11 | 16 | 32 | 16 | 100 | 4 |
| BSP F11204520100 D | 1” | 11 | 20 | 45 | 20 | 100 | 5 |
BSPT(RC)55°英制錐度密封管螺紋銑刀SPT(RC)5InchPipe
特征 Features
■BSPT(RC)錐度管螺紋，加工材料鋁合金，不銹鋼,鈦合金效果很好，效率高
@=最佳Best O=適合Good
單位UNIT \mathbf { \bar { \rho } } = \mathbf { \rho } MM
| 产品编码 | 型号 | 螺距TPI | 刃径d1 | 刃长L1 | 柄径D | 总长L | 刃数F |
| BSP F28 6.0140660 D | 1/16 | 28 | 5.3 | 9.9 | 6.0 | 60 | 4 |
| BSP F28 8.0140860 D | 1/8 | 28 | 7.3 | 9.9 | 8.0 | 60 | 4 |
| BSPF19 8.0180860D | 1/4 | 19 | 7.0 | 14 | 8.0 | 60 | 4 |
| BSP F19 10201075 D | 1/4 | 19 | 9.0 | 15 | 10 | 75 | 4 |
| BSP F19 12251275 D | 3/8 | 19 | 11.0 | 14 | 12 | 75 | 4 |
| BSP F1412201275 D | 1/2 | 14 | 10.8 | 19 | 12 | 75 | 4 |
| BSPF1.0 163016100 D | 3/4 | 14 | 14.6 | 21 | 16 | 100 | 4 |
| BSP F11 163216100 D | 1” | 11 | 14.3 | 27 | 16 | 100 | 4 |
| BSP F11204520100 D | 1” | 11 | 17.38 | 42 | 20 | 100 | 5 |
NPTNPTF美制錐度螺紋銑刀 NPT NPTF American tapered thread millng cuter
特征 Features
■NPT一般密封螺紋，NPTF干密封螺紋，加工材料:不銹鋼、鈦合金效果很好，效率高。
=最佳Best O=適合Good
單位UNIT \mathbf { \bar { \rho } } = \mathbf { \rho } MM
NPT-60°美制錐度管螺紋
| 产品编码 | 型号 | 螺距TPI | 刃径d1 | 刃长L1 | 柄径D | 总长L | 刃数F |
| NPTF275.4940660D | 1/16 | 27 | 5.4 | 9.4 | 6.0 | 60 | 4 |
| NPTF277.4940860 D | 1/8 | 27 | 7.4 | 9.4 | 8.0 | 60 | 4 |
| NPT F187.11410860 D | 1/4 | 18 | 7.1 | 14.1 | 8.0 | 60 | 4 |
| NPT F189.11411075 D | 1/4 | 18 | 9.1 | 14.1 | 10 | 75 | 4 |
| NPT F18 11.11411275 D | 3/8 | 18 | 11.1 | 14.1 | 12 | 75 | 4 |
| NPT F1410.81811275 D | 1/2 | 14 | 10.8 | 18.1 | 12 | 75 | 4 |
| NPT F1414.818116100 D | 3/4 | 14 | 14.8 | 18.1 | 16 | 100 | 4 |
| NPT F11.5 14.62216100 D | 1” | 11.5 | 14.6 | 22 | 16 | 100 | 4 |
| NPT F11.517.684520100 D | 1” | 11.5 | 17.38 | 42 | 20 | 100 | 5 |
NPTF-60°美制錐度密封管螺紋
| 产品编码 | 型号 | 螺距TPI | 刃径d1 | 刃长L1 | 柄径D | 总长L | 刃数F |
| NPTFF275.4940660 D | 1/16 | 27 | 5.4 | 9.4 | 6.0 | 60 | 4 |
| NPTF F277.4940860 D | 1/8 | 27 | 7.4 | 9.4 | 8.0 | 60 | 4 |
| NPTFF187.11410860 D | 1/4 | 18 | 7.1 | 14.1 | 8.0 | 60 | 4 |
| NPTFF189.11411075D | 1/4 | 18 | 9.1 | 14.1 | 10 | 75 | 4 |
| NPTF F1811.11411275 D | 3/8 | 18 | 11.1 | 14.1 | 12 | 75 | 4 |
| NPTFF1410.81811275D | 1/2 | 14 | 10.8 | 18.1 | 12 | 75 | 4 |
| NPTFF1414.818116100 D | 3/4 | 14 | 14.8 | 18.1 | 16 | 100 | 4 |
| NPTFF11.514.62216100 D | 1” | 11.5 | 14.6 | 22 | 16 | 100 | 4 |
| NPTFF11.517.684520100 D | 1” | 11.5 | 17.38 | 42 | 20 | 100 | 5 |
公制超硬二排牙螺紋銑刀 Metric Super Hard Two-Row Thread Milling Cutter
特征 Features
■第一排矮齒用來初加工，第二排牙齒精加工完成螺紋。刀具左旋設計，主軸需要反轉左旋左切減少讓刀增加切削力度。合適加工48HRC以上淬火鋼模具鋼等高硬材料
單位UNIT \dot { \bf { \rho } } = { \bf \rho } MM
| 产品编码 | 尺寸 | 螺距P | 刃径d1 | 避空直径d2 | 避空长L1柄径D | 总长L | 刃数F | |
| ISO H0.35 1.20320650 H | M1.6 | 0.35 | 1.2 | 0.78 | 3.2 | 6.0 | 50 | 3 |
| ISO H0.41.550400650 H | M2.0 | 0.4 | 1.55 | 1.05 | 4.0 | 6.0 | 50 | 4 |
| ISO H0.45 2.00500650 H | M2.5 | 0.45 | 2.0 | 1.45 | 5.0 | 6.0 | 50 | 4 |
| ISO H0.52.40600650 H | M3.0 | 0.5 | 2.4 | 1.8 | 6.0 | 6.0 | 50 | 4 |
| ISO H0.73.150800650 H | M4.0 | 0.7 | 3.15 | 2.3 | 8.0 | 6.0 | 50 | 4 |
| ISO H0.84.05100650 H | M5.0 | 0.8 | 4.05 | 3.05 | 10 | 6.0 | 50 | 4 |
| ISO H1.0 4.8120650 H | M6.0 | 1.0 | 4.8 | 3.6 | 12 | 6.0 | 50 | 5 |
| ISO H1.25 6.5160860 H | M8.0 | 1.25 | 6.5 | 5.0 | 16 | 8.0 | 60 | 6 |
| ISO H1.5 8.2201075 H | M10 | 1.5 | 8.2 | 6.4 | 20 | 10 | 75 | 6 |
| ISO H1.759.6241075 H | M12 | 1.75 | 9.6 | 7.5 | 24 | 10 | 75 | 6 |
公制超硬二排牙螺紋銑刀工作原理：
公制超硬二排牙螺紋銑刀加工過程
免打底孔鋁用多功能螺紋銑刀 TungstenSteel Free Bottom Hole Multi-Function Thread Milling Cutter
特征 Features
■不需要預鉆孔，免打底孔螺紋銑刀可一次完成底孔、螺紋及倒角銑削加工搭配上七彩DLC涂層，在加工銅鋁合金等有色金屬時大大的提高效率、顛覆傳統加二
單位UNIT \mathbf { \bar { \rho } } = \mathbf { \rho } MM
| 产品编码 | 尺寸 | 螺距P | 刃径d1避空长L1柄径D | 总长 | 刃数F | ||
| ISO M0.351.150500450 DLC | M1.6 | 0.35 | 1.15 | 5.0 | 4.0 | 50 | 2 |
| ISOM0.41.50650450DLC | M2.0 | 0.4 | 1.5 | 6.5 | 4.0 | 50 | 2 |
| ISOM0.451.90700450DLC | M2.5 | 0.45 | 1.9 | 7.0 | 4.0 | 50 | 2 |
| ISOM0.52.40900650DLC | M3.0 | 0.5 | 2.4 | 9.0 | 6.0 | 50 | 3 |
| ISOM0.73.2110650DLC | M4.0 | 0.7 | 3.2 | 11 | 6.0 | 50 | 3 |
| ISOM0.83.9120650DLC | M5.0 | 0.8 | 3.9 | 12 | 6.0 | 50 | 3 |
| ISOM1.04.7140650DLC | M6.0 | 1.0 | 4.7 | 14 | 6.0 | 50 | 3 |
| ISOM1.256.5180860DLC | M8.0 | 1.25 | 6.5 | 18 | 8.0 | 60 | 4 |
| ISOM1.57.8230860DLC | M10 | 1.5 | 7.8 | 23 | 8.0 | 60 | 4 |
| ISOM1.759.6261075DLC | M12 | 1.75 | 9.6 | 26 | 10 | 75 | 4 |
免打底孔鋁用多功能螺紋銑刀加工過程：
免打底孔鋼用多功能螺紋銑刀 Tungstensteel free bottom hole multi-function thread milling cutter For Steel
特征 Features
■不需要預鉆孔，免打底孔螺紋銑刀可一次完成底孔、螺紋銑削加工采用高硬度涂層，在加工鋼件時大大提高了刀具的切削力度和壽命，顛覆傳統加工
單位UNIT=MM
| 产品编码 | 尺寸 | 螺距P | 刃径d1避空长L1柄径D总长L刃数F内冷/外冷 | |||||
| ISOM0.52.40700650A | M3.0 | 0.5 | 2.4 | 7.0 | 6.0 | 50 | 4 | 外冷 |
| ISOM0.73.20900650A | M4.0 | 0.7 | 3.2 | 9.0 | 6.0 | 50 | 4 | 外冷 |
| ISOM0.83.9120650A | M5.0 | 0.8 | 3.9 | 12 | 6.0 | 50 | 4 | 外冷 |
| ISOM1.04.7140650A | M6.0 | 1.0 | 4.7 | 14 | 6.0 | 50 | 4 | 外冷 |
| ISOM1.256.2180860A | M8.0 | 1.25 | 6.2 | 18 | 8.0 | 60 | 4 | 内冷 |
| ISOM1.57.5230860 A | M10 | 1.5 | 7.5 | 23 | 8.0 | 60 | 4 | 内冷 |
| ISOM1.759.0261075A | M12 | 1.75 | 9.0 | 26 | 10 | 75 | 4 | 内冷 |
免打底孔鋼用多功能螺紋銑刀加工過程：
特征 Features
■適合大批量同規格生產，三合一鉆銑螺紋銑刀一把刀可實現底孔加工、倒角和內螺紋加工可以不更換刀具，減少非加工時間，提高生產效率。適合銅合金、鋁合金等有色金屬等
單位UNIT \mathbf { \bar { \rho } } = \mathbf { \rho } MM
| 产品编码 | 型号 | 螺纹外径d2 | 钻头径d1 | 刃长L1 | 钻头长L2 | 颈径D1 | 柄径D | 总长L | 刃数F |
| ISO DR1.0 5.0120860 A | M6*1.0 | 4.8 | 5.0 | 12 | 1.0 | 7.0 | 8.0 | 60 | 2 |
| ISODR1.256.0151075A | M8*1.25 | 6.5 | 6.8 | 15 | 1.3 | 9.0 | 10 | 75 | 2 |
| ISO DR1.5 8.5201275 A | M10*1.5 | 8.2 | 8.5 | 20 | 1.5 | 11 | 12 | 75 | 2 |
| ISO DR1.7510.32414100 A | M12*1.75 | 9.9 | 10.3 | 24 | 1.8 | 13.5 | 14 | 75 | 2 |
三合一鉆銑螺紋銑刀加工過程：
特征 Features
■適合大批量同規格生產，三合一鉆銑螺紋銑刀一把刀可實現底孔加工、倒角和內螺紋加工可以不更換刀具，減少非加工時間，提高生產效率。適合銅合金、鋁合金等有色金屬等
單位UNIT \mathbf { \bar { \rho } } = \mathbf { \rho } MM
| 产品编码 | 型号 | 螺纹外径d2 | 钻头径d1刃长L1 | 钻头长L2 | 颈径D1 | 柄径D | 总长L | 刃数F | |
| ISO DR1.0 5.0120860 DLC | M6*1.0 | 4.8 | 5.0 | 12 | 1.0 | 7.0 | 8.0 | 60 | 2 |
| ISO DR1.256.0151075 DLC | M8*1.25 | 6.5 | 6.8 | 15 | 1.3 | 9.0 | 10 | 75 | 2 |
| ISO DR1.58.5201275 DLC | M10*1.5 | 8.2 | 8.5 | 20 | 1.5 | 11 | 12 | 75 | 2 |
| ISO DR1.7510.32414100 DLC | M12*1.75 | 9.9 | 10.3 | 24 | 1.8 | 13.5 | 14 | 75 | 2 |
三合一鉆銑螺紋銑刀加工過程：
鎢鋼錐度醫療骨板螺紋銑刀 TungstenSteelTaperMedical Bone PlateThread Milling Cutter
特征 Features
■針對鈦合金骨板材料專用加工螺紋銑刀，光潔度高，排削順暢，尺寸穩定，耐磨持久特有的錐度螺旋槽，使刀具更耐用
@=最佳Best O=適合Good
公制60度錐度螺紋銑刀
單位UNIT \mathbf { \bar { \rho } } = \mathbf { \rho } MM
單位UNIT \mathbf { \bar { \rho } } = \mathbf { \rho } MM
| 产品编码 | 牙距P | 牙型角 | 刃径d1 | 角度° | 刃长L1 | 柄径D | 总长L |
| ISOTA0.31.9060660 A | 0.3 | 60° | 1.9 | 20° | 6.0 | 6.0 | 60 |
| ISO TA0.42.3100660 A | 0.4 | 60° | 2.3 | 20° | 10 | 6.0 | 60 |
| ISO TA0.5 2.9090660 A | 0.5 | 60° | 2.9 | 20° | 9.0 | 6.0 | 60 |
| ISOTA0.63.0140860 A | 0.6 | 60° | 3.0 | 20° | 14 | 8.0 | 60 |
英制55度錐度螺紋銑刀
| 产品编码 | 牙距P | 牙型角 | 刃径d1 | 角度° | 刃长L1 | 柄径D | 总长L |
| WTA0.31.9060660 A | 0.3 | 55° | 1.9 | 20° | 6.0 | 6.0 | 60 |
| WTA0.42.3100660A | 0.4 | 55° | 2.3 | 20° | 10 | 6.0 | 60 |
| WTA0.52.9090660A | 0.5 | 55° | 2.9 | 20° | 9.0 | 6.0 | 60 |
| WTA0.63.0140860A | 0.6 | 55° | 3.0 | 20° | 14 | 8.0 | 60 |
特征 Features
■全磨制一次成型，精準圓弧，拋光鈍化，定位面準，光潔度亮，耐磨性高
=最佳Best O=適合Good
單位UNIT MM
| 产品编码 | 型号 | 刃径d1 | R | 切深Q | 避空长L1 | 柄径D | 总长L |
| NTR08R005L3.00450 | NTR0.9 | 0.8 | 0.05 | 0.1 | 3.0 | 4.0 | 50 |
| NTR09R005L3.00450 | NTR1.0 | 0.9 | 0.05 | 0.1 | 3.0 | 4.0 | 50 |
| NTR11R005L4.00450 | NTR1.2 | 1.1 | 0.05 | 0.15 | 4.0 | 4.0 | 50 |
| NTR13R005L5.00450 | NTR1.4 | 1.3 | 0.05 | 0.15 | 5.0 | 4.0 | 50 |
| NTR15R005L6.00450 | NTR1.6 | 1.5 | 0.05 | 0.2 | 6.0 | 4.0 | 50 |
| NTR17R005L7.00450 | NTR1.8 | 1.7 | 0.05 | 0.2 | 7.0 | 4.0 | 50 |
| NTR17R020L7.00450 | NTR1.8 | 1.7 | 0.1 | 0.2 | 7.0 | 4.0 | 50 |
| NTR19R005L8.00450 | NTR2.0 | 1.9 | 0.05 | 0.25 | 8.0 | 4.0 | 50 |
| NTR19R010L8.00450 | NTR2.0 | 1.9 | 0.1 | 0.25 | 8.0 | 4.0 | 50 |
| NTR24R005L100450 | NTR2.5 | 2.4 | 0.05 | 0.3 | 10 | 4.0 | 50 |
| NTR24R010L100450 | NTR2.5 | 2.4 | 0.1 | 0.3 | 10 | 4.0 | 50 |
| NTR28R005L8.00450 | NTR3.0 | 2.8 | 0.05 | 0.3 | 8.0 | 4.0 | 50 |
| NTR28R005L120450 | NTR3.0 | 2.8 | 0.05 | 0.3 | 12 | 4.0 | 50 |
| NTR28R005L150450 | NTR3.0 | 2.8 | 0.05 | 0.3 | 15 | 4.0 | 50 |
| NTR28R010L8.00450 | NTR3.0 | 2.8 | 0.1 | 0.3 | 8.0 | 4.0 | 50 |
| NTR28R010L120450 | NTR3.0 | 2.8 | 0.1 | 0.3 | 12 | 4.0 | 50 |
| NTR28R010L150450 | NTR3.0 | 2.8 | 0.1 | 0.3 | 15 | 4.0 | 50 |
| NTR28R015L8.00450 | NTR3.0 | 2.8 | 0.15 | 0.3 | 8.0 | 4.0 | 50 |
| NTR28R015L120450 | NTR3.0 | 2.8 | 0.15 | 0.3 | 12 | 4.0 | 50 |
| NTR28R015L150450 | NTR3.0 | 2.8 | 0.15 | 0.3 | 15 | 4.0 | 50 |
| NTR28R020L0800450 | MTR3.0 | 2.8 | 0.2 | 0.3 | 8.0 | 4.0 | 50 |
| NTR28R020L150450 | MTR3.0 | 2.8 | 0.2 | 0.3 | 15 | 4.0 | 50 |
| NTR34R005L150450 | NTR3.5 | 3.4 | 0.05 | 0.35 | 15 | 4.0 | 50 |
| NTR34R010L150450 | NTR3.5 | 3.4 | 0.1 | 0.35 | 15 | 4.0 | 50 |
| NTR34R015L150450 | NTR3.5 | 3.4 | 0.15 | 0.35 | 15 | 4.0 | 50 |
| NTR34R020L150450 | NTR3.5 | 3.4 | 0.2 | 0.35 | 15 | 4.0 | 50 |
| NTR34R020L220450 | NTR3.5 | 3.4 | 0.2 | 0.35 | 22 | 4.0 | 50 |
| NTR39R005L100450 | NTR4.0 | 3.9 | 0.05 | 0.45 | 10 | 4.0 | 50 |
| NTR39R005L150450 | NTR4.0 | 3.9 | 0.05 | 0.45 | 15 | 4.0 | 50 |
| NTR39R005L220450 | NTR4.0 | 3.9 | 0.05 | 0.45 | 22 | 4.0 | 50 |
| NTR39R010L100450 | NTR4.0 | 3.9 | 0.1 | 0.45 | 10 | 4.0 | 50 |
| NTR39R010L150450 | NTR4.0 | 3.9 | 0.1 | 0.45 | 15 | 4.0 | 50 |
| NTR39R010L220450 | NTR4.0 | 3.9 | 0.1 | 0.45 | 22 | 4.0 | 50 |
| NTR39R015L100450 | NTR4.0 | 3.9 | 0.15 | 0.45 | 10 | 4.0 | 50 |
| NTR39R015L150450 | NTR4.0 | 3.9 | 0.15 | 0.45 | 15 | 4.0 | 50 |
特征 Features
■全磨制一次成型，精準圓弧，拋光鈍化，定位面準，光潔度亮，耐磨性高
=最佳Best O=適合Good
單位UNIT \dot { \bf \Phi } = \bf \Phi MM
| 产品编码 | 型号 | 刃径d1 | R | 切深Q | 避空长L1 | 柄径D | 总长L |
| NTR39R015L220450 | NTR4.0 | 3.9 | 0.15 | 0.45 | 22 | 4.0 | 50 |
| NTR39R020L100450 | NTR4.0 | 3.9 | 0.2 | 0.45 | 10 | 4.0 | 50 |
| NTR39R020L150450 | NTR4.0 | 3.9 | 0.2 | 0.45 | 15 | 4.0 | 50 |
| NTR39R020L220450 | NTR4.0 | 3.9 | 0.2 | 0.45 | 22 | 4.0 | 50 |
| NTR39R020L200475 | NTR4.0 | 3.9 | 0.2 | 0.45 | 20 | 4.0 | 75 |
| NTR39R020L2504100 | NTR4.0 | 3.9 | 0.2 | 0.45 | 25 | 4.0 | 100 |
| NTR45R020L150550 | NTR4.6 | 4.5 | 0.2 | 0.5 | 15 | 5.0 | 50 |
| NTR45R020L220550 | NTR4.6 | 4.5 | 0.2 | 0.5 | 22 | 5.0 | 50 |
| NTR49R005L150550 | NTR5.0 | 4.9 | 0.05 | 0.55 | 15 | 5.0 | 50 |
| NTR49R005L220550 | NTR5.0 | 4.9 | 0.05 | 0.55 | 22 | 5.0 | 50 |
| NTR49R010L150550 | NTR5.0 | 4.9 | 0.1 | 0.55 | 15 | 5.0 | 50 |
| NTR49R010L220550 | NTR5.0 | 4.9 | 0.1 | 0.55 | 22 | 5.0 | 50 |
| NTR49R020L150550 | NTR5.0 | 4.9 | 0.2 | 0.55 | 15 | 5.0 | 50 |
| NTR49R020L200550 | NTR5.0 | 4.9 | 0.2 | 0.55 | 20 | 5.0 | 50 |
| NTR49R020L220550 | NTR5.0 | 4.9 | 0.2 | 0.55 | 22 | 5.0 | 50 |
| NTR49R020L300560 | NTR5.0 | 4.9 | 0.2 | 0.55 | 30 | 5.0 | 60 |
| NTR49R020L250575 | NTR5.0 | 4.9 | 0.2 | 0.55 | 25 | 5.0 | 75 |
| NTR49R020L3005100 | NTR5.0 | 4.9 | 0.2 | 0.55 | 30 | 5.0 | 100 |
| NTR54R020L200650 | NTR5.5 | 5.4 | 0.2 | 0.65 | 20 | 6.0 | 50 |
| NTR59R005L150650 | NTR6.0 | 5.9 | 0.05 | 0.65 | 15 | 6.0 | 50 |
| NTR59R005L220650 | NTR6.0 | 5.9 | 0.05 | 0.65 | 22 | 6.0 | 50 |
| NTR59R010L150650 | NTR6.0 | 5.9 | 0.1 | 0.65 | 15 | 6.0 | 50 |
| NTR59R010L220650 | NTR6.0 | 5.9 | 0.1 | 0.65 | 22 | 6.0 | 50 |
| NTR59R020L150650 | NTR6.0 | 5.9 | 0.2 | 0.65 | 15 | 6.0 | 50 |
| NTR59R020L220650 | NTR6.0 | 5.9 | 0.2 | 0.65 | 22 | 6.0 | 50 |
| NTR59R020L300660 | NTR6.0 | 5.9 | 0.2 | 0.65 | 30 | 6.0 | 60 |
| NTR59R020L300675 | NTR6.0 | 5.9 | 0.2 | 0.65 | 25 | 6.0 | 75 |
| NTR59R020L3006100 | NTR6.0 | 5.9 | 0.2 | 0.65 | 30 | 6.0 | 100 |
| NTR59R040L150650 | MTR6.0 | 5.9 | 0.4 | 0.65 | 15 | 6.0 | 50 |
| NTR59R040L220650 | MTR6.0 | 5.9 | 0.4 | 0.65 | 22 | 6.0 | 50 |
| NTR69R020L220860 | NTR7.0 | 6.9 | 0.2 | 0.75 | 22 | 8.0 | 60 |
| NTR69R020L300860 | NTR7.0 | 6.9 | 0.2 | 0.75 | 30 | 8.0 | 60 |
| NTR79R010L300860 | NTR8.0 | 7.9 | 0.1 | 0.85 | 30 | 8.0 | 60 |
| NTR79R020L300860 | NTR8.0 | 7.9 | 0.2 | 0.85 | 30 | 8.0 | 60 |
| NTR79R020L3008100 | NTR8.0 | 7.9 | 0.2 | 0.85 | 30 | 8.0 | 100 |
NNR鎢鋼不開槽小孔鏜刀 NNR Tungsten Steel Non-Grooving MINI Boring Tool
特征 Features
■全磨制一次成型，精準圓弧，拋光鈍化，定位面準，光潔度亮，耐磨性高
=最佳Best O=適合Good
| P | H | K | M | N | S | |||||||||
| 碳素钢 | 合金钢 | 预硬钢 | 淬火钢钢 Hardened Steel | 铸铁不锈钢 | 铝合金铜合金 | 塑胶 | 亚克力高温合金钛合金 | |||||||
| Carben | AlloySteel | Prehardened | ~48HRC | ~55HRC~60HRC | ~65HRC | Cast Iron | Stainlee | Aluminium | CAlpyer | Cemstint | Acrylic | |||
| O | O | O | ||||||||||||
單位UNIT \mathbf { \bar { \rho } } = \mathbf { \rho } MM
| 产品编码 | 型号 | 刃径d1 | 深度Q | 避空长L1 | 柄径D | 总长L | |
| NNR09R005L030450 | MNR1.0 | 0.9 | 0.05 | 0.1 | 3 | 4.0 | 50 |
| NNR11R015L040450 | MNR1.2 | 1.1 | 0.05 | 0.15 | 4 | 4.0 | 50 |
| NNR13R005L050450 | MNR1.4 | 1.3 | 0.05 | 0.15 | 5 | 4.0 | 50 |
| NNR15R005L060450 | MNR1.6 | 1.5 | 0.05 | 0.2 | 6 | 4.0 | 50 |
| NNR17R010L070450 | MNR1.8 | 1.7 | 0.1 | 0.2 | 7 | 4.0 | 50 |
| NNR19R010L080450 | MNR2.0 | 1.9 | 0.1 | 0.25 | 8 | 4.0 | 50 |
| NNR19R010L100450 | MNR2.0 | 1.9 | 0.1 | 0.25 | 10 | 4.0 | 50 |
| NNR24R010L100450 | MNR2.5 | 2.4 | 0.1 | 0.3 | 10 | 4.0 | 50 |
| NNR24R010L150450 | MNR2.5 | 2.4 | 0.1 | 0.3 | 15 | 4.0 | 50 |
| NNR28R010L80450 | MNR3.0 | 2.8 | 0.1 | 0.3 | 8 | 4.0 | 50 |
| NNR28R010L120450 | MNR3.0 | 2.8 | 0.1 | 0.3 | 12 | 4.0 | 50 |
| NNR28R010L150450 | MNR3.0 | 2.8 | 0.1 | 0.3 | 15 | 4.0 | 50 |
| NNR28R015L120450 | MNR3.0 | 2.8 | 0.15 | 0.3 | 12 | 4.0 | 50 |
| NNR28R020L120450 | MNR3.0 | 2.8 | 0.2 | 0.3 | 12 | 4.0 | 50 |
| NNR28R020L150450 | MNR3.0 | 2.8 | 0.2 | 0.3 | 15 | 4.0 | 50 |
| NNR39R010L100450 | MNR4.0 | 3.9 | 0.1 | 0.45 | 10 | 4.0 | 50 |
| NNR39R010L150450 | MNR4.0 | 3.9 | 0.1 | 0.45 | 15 | 4.0 | 50 |
| NNR39R020L100450 | MNR4.0 | 3.9 | 0.2 | 0.45 | 10 | 4.0 | 50 |
| NNR39R020L150450 | MNR4.0 | 3.9 | 0.2 | 0.45 | 15 | 4.0 | 50 |
| NNR39R020L220450 | MNR4.0 | 3.9 | 0.2 | 0.45 | 22 | 4.0 | 50 |
| NNR39R040L150450 | MNR4.0 | 3.9 | 0.4 | 0.45 | 15 | 4.0 | 50 |
| NNR49R020L150550 | MNR5.0 | 4.9 | 0.2 | 0.55 | 15 | 5.0 | 50 |
| NNR49R020L220550 | MNR5.0 | 4.9 | 0.2 | 0.55 | 22 | 5.0 | 50 |
| NNR49R040L220550 | MNR5.0 | 4.9 | 0.4 | 0.55 | 22 | 5.0 | 50 |
| NNR59R020L150650 | MNR6.0 | 5.9 | 0.2 | 0.65 | 15 | 6.0 | 50 |
| NNR59R020L220650 | MNR6.0 | 5.9 | 0.2 | 0.65 | 22 | 6.0 | 50 |
| NNR59R040L220650 | MNR6.0 | 5.9 | 0.4 | 0.65 | 22 | 6.0 | 50 |
| NNR79R020L320860 | MNR8.0 | 7.9 | 0.2 | 0.85 | 32 | 8.0 | 60 |
NIR鎢鋼小孔螺紋車刀(正手/右手) NIRTungsten Steel Mini Thread Turning Tool(Forehand/Right)
特征 Features
■全磨制一次成型，精準圓弧，拋光鈍化，定位面準，光潔度亮，耐磨性高
單位UNIT=MM
| 产品编码 | 型号 | 刃径d1 | R | 角度° | 牙距 | 避空长L1 | 柄径D | 总长L |
| NIR14R003L040450A60 | NIR1.5 | 1.4 | 0.03 | 60° | 0.3-0.4 | 4.0 | 4.0 | 50 |
| NIR19R003L040450A60 | NIR2.0 | 1.9 | 0.03 | 60° | 0.3-0.5 | 4.0 | 4.0 | 49 |
| NIR19R003L060450A60 | NIR2.0 | 1.9 | 0.03 | 60° | 0.3-0.5 | 6.0 | 4.0 | 50 |
| NIR24R003L050455A60 | NIR2.5 | 2.4 | 0.03 | 60° | 0.3-0.6 | 5.0 | 4.0 | 50 |
| NIR24R003L070450A60 | NIR2.5 | 2.4 | 0.03 | 60° | 0.3-0.6 | 7.0 | 4.0 | 50 |
| NIR29R005L060450A60 | NIR3.0 | 2.9 | 0.05 | 60° | 0.5-0.8 | 6.0 | 4.0 | 50 |
| NIR29R005L100450A60 | NIR3.0 | 2.9 | 0.05 | 60° | 0.5-0.8 | 10 | 4.0 | 50 |
| NIR39R005L080450A60 | NIR4.0 | 3.9 | 0.05 | 60° | 0.5-1.0 | 8.0 | 4.0 | 50 |
| NIR39R005L120450A60 | NIR4.0 | 3.9 | 0.05 | 60° | 0.5-1.0 | 12 | 4.0 | 50 |
| NIR49R010L120550A60 | NIR5.0 | 4.9 | 0.1 | 60° | 0.8-1.25 | 12 | 5.0 | 50 |
| NIR49R010L150550A60 | NIR5.0 | 4.9 | 0.1 | 60° | 0.8-1.25 | 15 | 5.0 | 50 |
| NIR59R010L150650A60 | NIR6.0 | 5.9 | 0.1 | 60° | 0.8-1.5 | 15 | 6.0 | 50 |
| NIR59R010L220650A60 | NIR6.0 | 5.9 | 0.1 | 60° | 0.8-1.5 | 22 | 6.0 | 50 |
| NIR79R010L220860A60 | NIR8.0 | 7.9 | 0.1 | 60° | 1.0-2.0 | 22 | 8.0 | 60 |
NIL鎢鋼小孔螺紋車刀(反手/左手) NILTungsten Steel Mini Thread Turning Tool(Backhand/Left Hand)
特征 Features
■全磨制一次成型，精準圓弧，拋光鈍化，定位面準，光潔度亮，耐磨性高
單位UNIT \mathbf { \Sigma } = \mathbf { \Sigma } MM
| 产品编码 | 型号 | 刃径d1 | R | 角度° | 牙距 | 避空长L1 | 柄径D | 总长L |
| NIL14R003L040450A60 | NIL1.5 | 1.4 | 0.03 | 60° | 0.3-0.4 | 4.0 | 4.0 | 50 |
| NIL19R003L060450A60 | NIL2.0 | 1.9 | 0.03 | 60° | 0.3-0.5 | 6.0 | 4.0 | 50 |
| NIL24R003L070450 A60 | NIL2.5 | 2.4 | 0.03 | 60° | 0.3-0.6 | 7.0 | 4.0 | 50 |
| NIL29R005L100450A60 | NIL3.0 | 2.9 | 0.05 | 60° | 0.5-0.8 | 10 | 4.0 | 50 |
| NIL39R005L120450 A60 | NIL4.0 | 3.9 | 0.05 | 60° | 0.5-1.0 | 12 | 4.0 | 50 |
| NIL49R010L150550A60 | NIL5.0 | 4.9 | 0.1 | 60° | 0.8-1.25 | 15 | 5.0 | 50 |
| NIL59R010L220650 A60 | NIL6.0 | 5.9 | 0.1 | 60° | 0.8-1.5 | 22 | 6.0 | 50 |
| NIL79R010L220860A60 | NIL8.0 | 7.9 | 0.1 | 60° | 1.0-2.0 | 22 | 8.0 | 60 |
NIR(55°鎢鋼英制小孔螺紋車刀(正手/右手)
特征 Features
■全磨制一次成型，精準圓弧，拋光鈍化，定位面準，光潔度亮，耐磨性高
單位UNIT \mathbf { \bar { \rho } } = \mathbf { \rho } MM
| 产品编码 | 型号 | 刃径d1 | R | 角度° | 避空长L1 | 柄径D | 总长L |
| NIR29R005L100450A55 | MIR3.0 | 2.9 | 0.05 | 55° | 10 | 4.0 | 50 |
| NIR39R005L120450A55 | MIR4.0 | 3.9 | 0.05 | 55° | 12 | 4.0 | 50 |
| NIR39R010L120450A55 | MIR4.0 | 3.9 | 0.1 | 55° | 12 | 4.0 | 50 |
| NIR49R005L150550A55 | MIR5.0 | 4.9 | 0.05 | 55° | 15 | 5.0 | 50 |
| NIR49R010L150550A55 | MIR5.0 | 4.9 | 0.1 | 55° | 15 | 5.0 | 50 |
| NIR59R005L220650A55 | MIR6.0 | 5.9 | 0.05 | 55° | 22 | 6.0 | 50 |
| NIR59R010L220650A55 | MIR6.0 | 5.9 | 0.1 | 55° | 22 | 6.0 | 50 |
| NIR79R010L220860A55 | MIR8.0 | 7.9 | 0.1 | 55° | 22 | 8.0 | 60 |
NIR(TR)鎢鋼梯形螺紋車刀(正手/右手)TR(TR)Mini Tuing
特征 Features
■全磨制一次成型，精準圓弧，拋光鈍化，定位面準，光潔度亮，耐磨性高
單位UNIT \mathbf { \bar { \rho } } = \mathbf { \rho } MM
| 产品编码 | 型号 | 刃径d1 | 角度° | 避空长L1 | 柄径D | 总长L |
| NIR56P15L200650 A30 | NIR 6D 20L 1.5 TR | 5.6 | 30° | 20 | 6.0 | 50 |
| NIR64P20L250860A30 | NIR 8D25L2.0 TR | 6.4 | 30° | 25 | 8.0 | 60 |
| NIR68P30L350875A30 | NIR 8D35L3.0TR | 6.8 | 30° | 35 | 8.0 | 75 |
| NIR96P20L351075A30 | NIR10D35L2.0 TR | 9.6 | 30° | 35 | 10 | 75 |
| NIR99P40L4510100 A30 | NIR 10D45L4.0 TR | 9.9 | 30° | 45 | 10 | 100 |
| NIR119P50L5012100A30 | NIR 12D 50L5.0 TR | 11.9 | 30° | 50 | 12 | 100 |
NIR(ACME)鎢鋼梯形螺紋車刀(正手/右手) NIR(TR) Mini Turning
特征 Features
■全磨制一次成型，精準圓弧，拋光鈍化，定位面準，光潔度亮，耐磨性高
單位UNIT=MM
| 产品编码 | 型号 | 刃径d1 | 角度° | 避空长L1 | 柄径D | 总长L |
| NIR39P16L150450A29 | NIR4D15L16ACME | 3.9 | 29° | 15 | 4.0 | 50 |
| NIR56P14L200650 A29 | NIR 6D20L14ACME | 5.6 | 29° | 20 | 6.0 | 50 |
| NIR66P12L250860A29 | NIR 8D 25L12 ACME | 6.6 | 29° | 25 | 8.0 | 60 |
| NIR79P10L300875A29 | NIR 8D30L10ACME | 7.9 | 29° | 30 | 8.0 | 75 |
| NIR99P8L351075A29 | NIR10D35L8ACME | 9.9 | 29° | 35 | 10 | 75 |
| NIR99P6L4510100 A29 | NIR 10D45L6ACME | 9.9 | 29° | 45 | 10 | 100 |
| NIR119P5L5012100 A29 | NIR12D50L5ACME | 11.9 | 29° | 50 | 12 | 100 |
特征 Features
■全磨制一次成型，精準圓弧，拋光鈍化，定位面準，光潔度亮，耐磨性高
單位UNIT=MM
| 产品编码 | 型号 | 刃径d1 | 宽度B | 深度Q | 避空长L1 | 柄径D | 总长L |
| NGR29B050L100450 | NGR3.0 | 2.9 | 0.5 | 0.8 | 10 | 4.0 | 50 |
| NGR29B075L100450 | NGR3.0 | 2.9 | 0.75 | 0.8 | 10 | 4.0 | 50 |
| NGR29B100L100450 | NGR3.0 | 2.9 | 1.0 | 0.8 | 10 | 4.0 | 50 |
| NGR29B150L100450 | NGR3.0 | 2.9 | 1.5 | 0.8 | 10 | 4.0 | 50 |
| NGR39B050L100450 | NGR4.0 | 3.9 | 0.5 | 1.0 | 10 | 4.0 | 50 |
| NGR39B080L100450 | NGR4.0 | 3.9 | 0.8 | 1.0 | 10 | 4.0 | 50 |
| NGR39B100L100450 | NGR4.0 | 3.9 | 1.0 | 1.0 | 10 | 4.0 | 50 |
| NGR39B150L100450 | NGR4.0 | 3.9 | 1.5 | 1.0 | 10 | 4.0 | 50 |
| NGR49B100L100550 | NGR5.0 | 4.9 | 1.0 | 1.5 | 10 | 5.0 | 50 |
| NGR49B120L100550 | NGR5.0 | 4.9 | 1.2 | 1.5 | 10 | 5.0 | 50 |
| NGR49B150L100550 | NGR5.0 | 4.9 | 1.5 | 1.5 | 10 | 5.0 | 50 |
| NGR49B200L100550 | NGR5.0 | 4.9 | 2.0 | 2.0 | 10 | 5.0 | 50 |
| NGR59B100L150650 | NGR6.0 | 5.9 | 1.0 | 2.0 | 15 | 6.0 | 50 |
| NGR59B150L150650 | NGR6.0 | 5.9 | 1.5 | 2.0 | 15 | 6.0 | 50 |
| NGR59B200L150650 | NGR6.0 | 5.9 | 2.0 | 2.5 | 15 | 6.0 | 50 |
| NGR59B250L150650 | NGR6.0 | 5.9 | 2.5 | 2.5 | 15 | 6.0 | 50 |
| NGR79B150L200860 | NGR8.0 | 7.9 | 1.5 | 2.0 | 20 | 8.0 | 60 |
| NGR79B200L200860 | NGR8.0 | 7.9 | 2.0 | 2.5 | 20 | 8.0 | 60 |
| NGR79B250L200860 | NGR8.0 | 7.9 | 2.5 | 3.0 | 20 | 8.0 | 60 |
| NGR79B300L200860 | NGR8.0 | 7.9 | 3.0 | 3.0 | 20 | 8.0 | 60 |
特征 Features
■全磨制一次成型，精準圓弧，拋光鈍化，定位面準，光潔度亮，耐磨性高
單位UNIT=MM
| 产品编码 | 型号 | 刃径d1 | R | 宽度B | 深度Q | 避空长L1 | 柄径D | 总长L |
| NKR39R050L100450 | NKR4.0 | 3.9 | 0.5 | 1.0 | 1.0 | 10 | 4.0 | 50 |
| NKR39R050L150450 | NKR4.0 | 3.9 | 0.5 | 1.0 | 1.0 | 15 | 4.0 | 50 |
| NKR39R075L100450 | NKR4.0 | 3.9 | 0.75 | 1.5 | 1.0 | 10 | 4.0 | 50 |
| NKR39R075L150450 | NKR4.0 | 3.9 | 0.75 | 1.5 | 1.0 | 15 | 4.0 | 50 |
| NKR49R050L150550 | NKR5.0 | 4.9 | 0.5 | 1.0 | 1.2 | 15 | 5.0 | 50 |
| NKR49R050L220550 | NKR5.0 | 4.9 | 0.5 | 1.0 | 1.2 | 22 | 5.0 | 50 |
| NKR49R075L150550 | NKR5.0 | 4.9 | 075 | 1.5 | 1.2 | 15 | 5.0 | 50 |
| NKR49R075L220550 | NKR5.0 | 4.9 | 0.75 | 1.5 | 1.2 | 22 | 5.0 | 50 |
| NKR49R100L150550 | NKR5.0 | 4.9 | 1.0 | 2.0 | 1.3 | 15 | 5.0 | 50 |
| NKR49R100L220550 | NKR5.0 | 4.9 | 1.0 | 2.0 | 1.3 | 22 | 5.0 | 50 |
| NKR59R050L150650 | NKR6.0 | 5.9 | 0.5 | 1.0 | 1.6 | 15 | 6.0 | 50 |
| NKR59R050L220650 | NKR6.0 | 5.9 | 0.5 | 1.0 | 1.6 | 22 | 6.0 | 50 |
| NKR59R075L150650 | NKR6.0 | 5.9 | 075 | 1.5 | 1.6 | 15 | 6.0 | 50 |
| NKR59R075L220650 | NKR6.0 | 5.9 | 0.75 | 1.5 | 1.6 | 22 | 6.0 | 50 |
| NKR59R100L150650 | NKR6.0 | 5.9 | 1.0 | 2.0 | 1.6 | 15 | 6.0 | 50 |
| NKR59R100L220650 | NKR6.0 | 5.9 | 1.0 | 2.0 | 1.6 | 22 | 6.0 | 50 |
| NKR79R050L220860 | NKR8.0 | 7.9 | 0.5 | 1.0 | 2.0 | 22 | 8.0 | 60 |
| NKR79R075L220860 | NKR8.0 | 7.9 | 0.75 | 1.5 | 2.0 | 22 | 8.0 | 60 |
| NKR79R100L220860 | NKR8.0 | 7.9 | 1.0 | 2.0 | 2.0 | 22 | 8.0 | 60 |
NFR鎢鋼端面槽刀(正手/右手 NFRTungstenSteelFaceGrooveTool (Forehand/Right)
特征 Features
■全磨制一次成型，精準圓弧，拋光鈍化，定位面準，光潔度亮，耐磨性高
單位UNIT \mathbf { \bar { \rho } } = \mathbf { \rho } MM
| 产品编码 | 型号 | 宽度B | 深度Q | 避空长L1 | 柄径D | 总长L |
| NFR40B050L1550 | NFR4.0 | 0.5 | 1.0 | 15 | 4.0 | 50 |
| NFR40B075L1550 | NFR4.0 | 0.75 | 1.2 | 15 | 4.0 | 50 |
| NFR40B100L1550 | NFR4.0 | 1.0 | 1.5 | 15 | 4.0 | 50 |
| NFR50B100L2250 | NFR5.0 | 1.0 | 2.0 | 22 | 5.0 | 50 |
| NFR50B150L2250 | NFR5.0 | 1.5 | 2.5 | 22 | 5.0 | 50 |
| NFR50B200L2250 | NFR5.0 | 2.0 | 3.0 | 22 | 5.0 | 50 |
| NFR60B050L2050 | NFR6.0 | 0.5 | 1.0 | 20 | 6.0 | 50 |
| NFR60B100L2050 | NFR6.0 | 1.0 | 2.0 | 20 | 6.0 | 50 |
| NFR60B150L2050 | NFR6.0 | 1.5 | 3.0 | 20 | 6.0 | 50 |
| NFR60B200L2050 | NFR6.0 | 2.0 | 4.0 | 20 | 6.0 | 50 |
| NFR80B100L2560 | NFR8.0 | 1.0 | 2.0 | 25 | 8.0 | 60 |
| NFR80B150L2560 | NFR8.0 | 1.5 | 3.0 | 25 | 8.0 | 60 |
| NFR80B200L2560 | NFR8.0 | 2.0 | 4.0 | 25 | 8.0 | 60 |
NFL鎢鋼端面槽刀(反手/左手） NFLTungsten Steel Face Groove Tool (Backhand/Left Hand)
特征 Features
■全磨制一次成型，精準圓弧，拋光鈍化，定位面準，光潔度亮，耐磨性高
單位UNIT \mathbf { \bar { \rho } } = \mathbf { \rho } MM
| 产品编码 | 型号 | 宽度B | 深度Q | 避空长L1 | 柄径D | 总长L |
| NFL40B050L1550 | NFL4.0 | 0.5 | 1.0 | 15 | 4.0 | 50 |
| NFL40B075L1550 | NFL4.0 | 0.75 | 1.2 | 15 | 4.0 | 50 |
| NFL40B100L1550 | NFL4.0 | 1.0 | 1.5 | 15 | 4.0 | 50 |
| NFL50B100L2250 | NFL5.0 | 1.0 | 2.0 | 22 | 5.0 | 50 |
| NFL50B150L2250 | NFL5.0 | 1.5 | 2.5 | 22 | 5.0 | 50 |
| NFL50B200L2250 | NFL5.0 | 2.0 | 3.0 | 22 | 5.0 | 50 |
| NFL60B050L2050 | NFL6.0 | 0.5 | 1.0 | 20 | 6.0 | 50 |
| NFL60B100L2050 | NFL6.0 | 1.0 | 2.0 | 20 | 6.0 | 50 |
| NFL60B150L2050 | NFL6.0 | 1.5 | 3.0 | 20 | 6.0 | 50 |
| NFL60B200L2050 | NFL6.0 | 2.0 | 4.0 | 20 | 6.0 | 50 |
| NFL80B100L2560 | NFL8.0 | 1.0 | 2.0 | 25 | 8.0 | 60 |
| NFL80B150L2560 | NFL8.0 | 1.5 | 3.0 | 25 | 8.0 | 60 |
| NFL80B200L2560 | NFL8.0 | 2.0 | 4.0 | 25 | 8.0 | 60 |
特征 Features
■全磨制一次成型，精準圓弧，拋光鈍化，定位面準，光潔度亮，耐磨性高
單位UNIT=MM
| 产品编码 | 型号 | 宽度B | 避空长L1 | 柄径D | 总长L |
| NVR60B200L1050 | NVR6.0 | 2.0 | 10 | 6.0 | 50 |
| NVR60B250L1050 | NVR6.0 | 2.5 | 10 | 6.0 | 50 |
| NVR60B200L1550 | NVR6.0 | 2.0 | 15 | 6.0 | 50 |
| NVR60B250L1550 | NVR6.0 | 2.5 | 15 | 6.0 | 50 |
| NVR80B250L2260 | NVR8.0 | 2.5 | 22 | 8.0 | 60 |
| NVR80B300L2260 | NVR8.0 | 3.0 | 22 | 8.0 | 60 |
| NVR80B400L2260 | NVR8.0 | 4.0 | 22 | 8.0 | 60 |
NZR鎢鋼圓弧端面槽刀(正手/右手) NZRTnovendit)
特征 Features
■全磨制一次成型，精準圓弧，拋光鈍化，定位面準，光潔度亮，耐磨性高
單位UNIT \mathbf { \bar { \rho } } = \mathbf { \rho } MM
| 产品编码 | 型号 | R | 宽度B | 深度Q | 避空长L1 | 柄径D | 总长L |
| NZR40B050L15R05050 | NZR4.0 | 0.5 | 1.0 | 1.2 | 15 | 4.0 | 50 |
| NZR40B075L15R05050 | NZR4.0 | 0.75 | 1.5 | 1.5 | 15 | 4.0 | 50 |
| NZR50B050L22R05050 | NZR5.0 | 0.5 | 1.0 | 1.2 | 22 | 5.0 | 50 |
| NZR50B075L22R05050 | NZR5.0 | 0.75 | 1.5 | 1.5 | 22 | 5.0 | 50 |
| NZR50B100L22R10050 | NZR5.0 | 1.0 | 2.0 | 2.5 | 22 | 5.0 | 50 |
| NZR60B050L22R05050 | NZR6.0 | 0.5 | 1.0 | 1.2 | 22 | 6.0 | 50 |
| NZR60B075L22R07550 | NZR6.0 | 0.75 | 1.5 | 1.5 | 22 | 6.0 | 50 |
| NZR60B100L22R10050 | NZR6.0 | 1.0 | 2.0 | 2.5 | 22 | 6.0 | 50 |
NZL鎢鋼圓弧端面槽刀(反手/左手) NZLTungstenSteelArcEndFace Groove Tool(Backhand/Left Hand)
特征 Features
■全磨制一次成型，精準圓弧，拋光鈍化，定位面準，光潔度亮，耐磨性高
單位UNIT \mathbf { \bar { \rho } } = \mathbf { \rho } MM
| 产品编码 | 型号 | R | 宽度B | 深度Q | 避空长L1 | 柄径D | 总长L |
| NZL40B050L15R05050 | NZL4.0 | 0.5 | 1.0 | 1.2 | 15 | 4.0 | 50 |
| NZL40B075L15R05050 | NZL4.0 | 0.75 | 1.5 | 1.5 | 15 | 4.0 | 50 |
| NZL50B050L22R05050 | NZL5.0 | 0.5 | 1.0 | 1.2 | 22 | 5.0 | 50 |
| NZL50B075L22R05050 | NZL5.0 | 0.75 | 1.5 | 1.5 | 22 | 5.0 | 50 |
| NZL50B100L22R10050 | NZL5.0 | 1.0 | 2.0 | 2.5 | 22 | 5.0 | 50 |
| NZL60B050L22R05050 | NZL6.0 | 0.5 | 1.0 | 1.2 | 22 | 6.0 | 50 |
| NZL60B075L22R07550 | NZL6.0 | 0.75 | 1.5 | 1.5 | 22 | 6.0 | 50 |
| NZL60B100L22R10050 | NZL6.0 | 1.0 | 2.0 | 2.5 | 22 | 6.0 | 50 |
特征 Features
■全磨制一次成型，精準圓弧，拋光鈍化，定位面準，光潔度亮，耐磨性高
@=最佳Best O=適合Good
單位UNIT=MM
| 产品编码 | 型号刃径d1 | R | 切深Q避空长L1柄径D总长L | ||||
| NPR08R005L030450 | NPR0.9 | 0.8 | 0.05 | 0.12 | 3.0 | 4.0 | 50 |
| NPR10R005L030450 | NPR1.1 | 1.0 | 0.05 | 0.15 | 3.0 | 4.0 | 50 |
| NPR12R005L0450450 | NPR1.3 | 1.2 | 0.05 | 0.15 | 4.5 | 4.0 | 50 |
| NPR14R005L050450 | NPR1.5 | 1.4 | 0.05 | 0.2 | 5.0 | 4.0 | 50 |
| NPR16R005L060450 | NPR1.7 | 1.6 | 0.05 | 0.3 | 6.0 | 4.0 | 50 |
| NPR18R005L070450 | NPR1.9 | 1.8 | 0.05 | 0.3 | 7.0 | 4.0 | 50 |
| NPR19R005L080450 | NPR2.0 | 1.9 | 0.05 | 0.4 | 8.0 | 4.0 | 50 |
| NPR19R010L080450 | NPR2.0 | 1.9 | 0.1 | 0.4 | 8.0 | 4.0 | 50 |
| NPR24R005L100450 | NPR2.5 | 2.4 | 0.05 | 0.5 | 10 | 4.0 | 50 |
| NPR24R010L100450 | NPR2.5 | 2.4 | 0.1 | 0.5 | 10 | 4.0 | 50 |
| NPR29R005L080450 | NPR3.0 | 2.9 | 0.05 | 0.6 | 8.0 | 4.0 | 50 |
| NPR29R010L080450 | NPR3.0 | 2.9 | 0.1 | 0.6 | 8.0 | 4.0 | 50 |
| NPR29R015L080450 | NPR3.0 | 2.9 | 0.15 | 0.6 | 8.0 | 4.0 | 50 |
| NPR29R005L120450 | NPR3.0 | 2.9 | 0.05 | 0.6 | 12 | 4.0 | 50 |
| NPR29R010L120450 | NPR3.0 | 2.9 | 0.1 | 0.6 | 12 | 4.0 | 50 |
| NPR29R015L120450 | NPR3.0 | 2.9 | 0.15 | 0.6 | 12 | 4.0 | 50 |
| NPR39R005L100450 | NPR4.0 | 3.9 | 0.05 | 0.8 | 10 | 4.0 | 50 |
| NPR39R010L100450 | NPR4.0 | 3.9 | 0.1 | 0.8 | 10 | 4.0 | 50 |
| NPR39R015L100450 | NPR4.0 | 3.9 | 0.15 | 0.8 | 10 | 4.0 | 50 |
| NPR39R005L150450 | NPR4.0 | 3.9 | 0.05 | 0.8 | 15 | 4.0 | 50 |
| NPR39R010L150450 | NPR4.0 | 3.9 | 0.1 | 0.8 | 15 | 4.0 | 50 |
| NPR39R015L150450 | NPR4.0 | 3.9 | 0.15 | 0.8 | 15 | 4.0 | 50 |
| NPR49R005L150550 | NPR5.0 | 4.9 | 0.05 | 1.0 | 15 | 5.0 | 50 |
| NPR49R010L150550 | NPR5.0 | 4.9 | 0.1 | 1.0 | 15 | 5.0 | 50 |
| NPR49R020L150550 | NPR5.0 | 4.9 | 0.2 | 1.0 | 15 | 5.0 | 50 |
| NPR49R005L220550 | NPR5.0 | 4.9 | 0.05 | 1.0 | 22 | 5.0 | 50 |
| NPR49R010L220550 | NPR5.0 | 4.9 | 0.1 | 1.0 | 22 | 5.0 | 50 |
| NPR49R020L220550 | NPR5.0 | 4.9 | 0.2 | 1.0 | 22 | 5.0 | 50 |
| NPR59R005L150650 | NPR6.0 | 5.9 | 0.05 | 1.2 | 15 | 6.0 | 50 |
| NPR59R010L150650 | NPR6.0 | 5.9 | 0.1 | 1.2 | 15 | 6.0 | 50 |
| NPR59R020L150650 | NPR6.0 | 5.9 | 0.2 | 1.2 | 15 | 6.0 | 50 |
| NPR59R005L220650 | NPR6.0 | 5.9 | 0.05 | 1.2 | 22 | 6.0 | 50 |
NPR鎢鋼小孔仿形鏜刀-2 NPR Tungsten Steel Mini Copy Boring Tool-2
特征 Features
■全磨制一次成型，精準圓弧，拋光鈍化，定位面準，光潔度亮，耐磨性高
單位UNIT=MM
| 产品编码 | 型号 | 刃径d1 | R | 切深Q | 避空长L1 | 柄径D | 总长L |
| NPR59R010L220650 | NPR6.0 | 5.9 | 0.1 | 1.2 | 22 | 6.0 | 50 |
| NPR59R020L220650 | NPR6.0 | 5.9 | 0.2 | 1.2 | 22 | 6.0 | 50 |
| NPR69R010L220860 | NPR7.0 | 6.9 | 0.1 | 1.5 | 22 | 8.0 | 60 |
| NPR69R020L220860 | NPR7.0 | 6.9 | 0.2 | 1.5 | 22 | 8.0 | 60 |
| NPR69R010L300860 | NPR7.0 | 6.9 | 0.1 | 1.5 | 30 | 8.0 | 60 |
| NPR69R020L300860 | NPR7.0 | 6.9 | 0.2 | 1.5 | 30 | 8.0 | 60 |
| NPR79R010L220860 | NPR8.0 | 7.9 | 0.1 | 1.8 | 22 | 8.0 | 60 |
| NPR79R020L220860 | NPR8.0 | 7.9 | 0.2 | 1.8 | 22 | 8.0 | 60 |
| NPR79R010L300860 | NPR8.0 | 7.9 | 0.1 | 1.8 | 30 | 8.0 | 60 |
| NPR79R020L300860 | NPR8.0 | 7.9 | 0.2 | 1.8 | 30 | 8.0 | 60 |
特征 Features
■全磨制一次成型，精準圓弧，拋光鈍化，定位面準，光潔度亮，耐磨性高
單位UNIT=MM
| 产品编码 | 型号 | 刃径d1 | R | 切深Q | 避空长L1 | 柄径D | 总长L |
| NQR29R005L090450 | NQR3.0 | 2.9 | 0.05 | 0.7 | 9 | 4.0 | 50 |
| NQR29R010L090450 | NQR3.0 | 2.9 | 0.1 | 0.7 | 9 | 4.0 | 50 |
| NQR29R015L090450 | NQR3.0 | 2.9 | 0.15 | 0.7 | 9 | 4.0 | 50 |
| NQR39R005L100450 | NQR4.0 | 3.9 | 0.05 | 1.0 | 10 | 4.0 | 50 |
| NQR39R010L100450 | NQR4.0 | 3.9 | 0.1 | 1.0 | 10 | 4.0 | 50 |
| NQR39R020L100450 | NQR4.0 | 3.9 | 0.2 | 1.0 | 10 | 4.0 | 50 |
| NQR39R020L150450 | NQR4.0 | 3.9 | 0.2 | 1.0 | 15 | 4.0 | 50 |
| NQR49R005L150550 | NQR5.0 | 4.9 | 0.05 | 1.2 | 15 | 5.0 | 50 |
| NQR49R010L150550 | NQR5.0 | 4.9 | 0.1 | 1.2 | 15 | 5.0 | 50 |
| NQR49R020L150550 | NQR5.0 | 4.9 | 0.2 | 1.2 | 15 | 5.0 | 50 |
| NQR49R020L200550 | NQR5.0 | 4.9 | 0.2 | 1.2 | 20 | 5.0 | 50 |
| NQR59R005L150650 | NQR6.0 | 5.9 | 0.5 | 1.6 | 15 | 6.0 | 50 |
| NQR59R010L150650 | NQR6.0 | 5.9 | 0.1 | 1.6 | 15 | 6.0 | 50 |
| NQR59R020L150650 | NQR6.0 | 5.9 | 0.2 | 1.6 | 15 | 6.0 | 50 |
| NQR59R020L220650 | NQR6.0 | 5.9 | 0.2 | 1.6 | 22 | 6.0 | 50 |
| NQR79R010L250860 | NQR8.0 | 7.9 | 0.1 | 2.1 | 25 | 8.0 | 60 |
| NQR79R020L250860 | NQR8.0 | 7.9 | 0.2 | 2.1 | 25 | 8.0 | 60 |
NUR鎢鋼90°小孔仿形鏜刀 NUR Tungsten Steel 9 0 ^ { \circ } Mini Copy Boring Tool
特征 Features
■全磨制一次成型，精準圓弧，拋光鈍化，定位面準，光潔度亮，耐磨性高
單位UNIT \mathbf { \bar { \rho } } = \mathbf { \rho } MM
| 产品编码 | 型号 | 刃径d1 | R | 切深Q | 避空长L1 | 柄径D | 总长L |
| NUR28R010L100450 | NUR3.0 | 2.8 | 0.1 | 0.5 | 10 | 4.0 | 50 |
| NUR28R010L150450 | NUR3.0 | 2.8 | 0.1 | 0.5 | 15 | 4.0 | 50 |
| NUR39R010L100450 | NUR4.0 | 3.9 | 0.1 | 0.6 | 10 | 4.0 | 50 |
| NUR39R010L150450 | NUR4.0 | 3.9 | 0.1 | 0.6 | 15 | 4.0 | 50 |
| NUR49R015L150550 | NUR5.0 | 4.9 | 0.15 | 0.8 | 15 | 5.0 | 50 |
| NUR49R015L220550 | NUR5.0 | 4.9 | 0.15 | 0.8 | 22 | 5.0 | 50 |
| NUR59R020L150650 | NUR6.0 | 5.9 | 0.2 | 1.0 | 15 | 6.0 | 50 |
| NUR59R020L220650 | NUR6.0 | 5.9 | 0.2 | 1.0 | 22 | 6.0 | 50 |
| NUR79R020L150860 | NUR8.0 | 7.9 | 0.2 | 1.2 | 22 | 8.0 | 60 |
特征 Features
■全磨制一次成型，精準圓弧，拋光鈍化，定位面準，光潔度亮，耐磨性高
單位UNIT=MM
| 产品编码 | 型号 | 刃径d1 | R | 宽度B | 深度Q | 避空长L1 | 柄径D | 总长L |
| NXR28R010L100450 | NXR3.0 | 2.8 | 0.1 | 1.3 | 0.5 | 10 | 4.0 | 50 |
| NXR39R015L100450 | NXR4.0 | 3.9 | 0.15 | 1.3 | 0.8 | 10 | 4.0 | 50 |
| NXR39R015L150450 | NXR4.0 | 3.9 | 0.15 | 1.3 | 0.8 | 15 | 4.0 | 50 |
| NXR49R020L150550 | NXR5.0 | 4.9 | 0.2 | 1.5 | 1.0 | 15 | 5.0 | 50 |
| NXR49R020L220550 | NXR5.0 | 4.9 | 0.2 | 1.5 | 1.0 | 22 | 5.0 | 50 |
| NXR59R020L150650 | NXR6.0 | 5.9 | 0.2 | 1.5 | 1.8 | 15 | 6.0 | 50 |
| NXR59R020L220650 | NXR6.0 | 5.9 | 0.2 | 1.5 | 1.8 | 22 | 6.0 | 50 |
特征 Features
■適合加工工件需要反面倒角的，可以在不翻面的情況下進行倒角，即節省了時間又保證了工件的同心度
=最佳Best O=適合Good
| P | H | K | M | N | S | |||||||||
| 碳素钢 | 合金钢 | 预硬钢 | 淬火钢钢HardenedSteel | 铸铁不锈钢铝合金 | 铜合金 | 塑胶 | 亚克力高温合金钛合金 | |||||||
| Carbeon | AlloySteel | Prehardened | ~48HRC | ~55HRC~60HRC | ~65HRC | Cast Iron | Stainle | Aluminium | Alpysr | Cemtint | Acrylic | |||
單位UNIT=MM
| 产品编码 | 刃径d1 | 倒角角度 | 避空长直径d2 | 避空长L1 | 柄径D | 总长L | 刃数F |
| UL C90 1.96080450A | 1.96 | 90° | 1.0 | 8 | 4.0 | 50 | 3 |
| UL C90 2.4100450A | 2.4 | 90° | 1.4 | 10 | 4.0 | 50 | 3 |
| UL C90 3.0150450 A | 3.0 | 90° | 1.8 | 15 | 4.0 | 50 | 3 |
| UL C90 4.0160450A | 4.0 | 90° | 2.4 | 16 | 4.0 | 50 | 3 |
| UL C904.5200650A | 4.5 | 90° | 2.3 | 20 | 6.0 | 50 | 4 |
| ULC90 5.0200650A | 5.0 | 90° | 2.8 | 20 | 6.0 | 50 | 4 |
| UL C90 6.0250650 A | 6.0 | 90° | 3.0 | 24 | 6.0 | 50 | 4 |
| ULC908.0280860A | 8.0 | 90° | 4.8 | 28 | 8.0 | 60 | 4 |
| UL C9010351075A | 10 | 90° | 6.4 | 35 | 10 | 75 | 4 |
| UL C90 125012100 A | 12 | 90° | 7.0 | 50 | 12 | 100 | 4 |
特征 Features
■配合美制英制錐管螺紋，加工錐度螺紋底孔，使螺紋精度更高
| P | H | K | M | N | S | |||||||||
| 碳素钢 | 合金钢 | 预硬钢 | 淬火钢钢Hardened Steel | 铸铁不锈钢铝合金铜合金 | 塑胶 | 亚克力高温合金钛合金 | ||||||||
| Carben | AlloySteel | Prehardened | ~48HRC | ~55HRC~60HRC | ~65HRC | Cast Iron | Stainle | Aluminium | Alpysr | Cemeint | Acrylic | |||
| O | ||||||||||||||
單位UNIT = MM
| 加工型号 | 刃径d1 | 避空长L1 | 柄径D | 总长L | 刃数F |
| NPT1/16”-1/8” NPTF 1/16” -1/8” BSPT1/16” -1/8” | 5.2 | 12 | 6 | 50 | 4 |
| NPT1/4”-1” NPTF1/4”-1” BSPT1/4”-1” | 8.5 | 24 | 10 | 75 | 4 |
| NPT1/4” -3” NPTF1/4”-3” BSPT1/4”-3” | 10 | 32 | 12 | 75 | 4 |
特征 Features
■鉆尖 1 8 0 ^ { \circ } 平底設計適合沉頭孔、斜面、曲面鉆孔加工，不易偏移歪斜，提高加工穩定性低螺旋、低前角設計，高光潔度，鋒利切割加工無毛刺，寬容排屑槽
| P | H | K | M | N | S | |||||||||
| 碳素钢 | 合金钢 | 预硬钢 | 淬火钢钢 Hardened Steel | 铸铁不锈钢铝合金 | 铜合金 | 塑胶 | 亚克力高温合金钛合金 | |||||||
| Carben | Alloy Steel | Prehardened | ~48HRC~55HRC~60HRC | ~65HRC | Cast Iron | Stainle | Aluminium | Calppyer | Cemstint | Acrylic | ||||
單位UNIT=MM
| 刃径d1 | 避空长L1 | 柄径D | 总长L |
| 0.5-1.0 | 4.0 | 3.0 | 50 |
| 1.05-1.5 | 6.0 | 3.0 | 50 |
| 1.55-1.95 | 10 | 3.0 | 50 |
| 2-2.95 | 14 | 4.0 | 50 |
| 3-4 | 17 | 4.0 | 50 |
| 4.05-5 | 23 | 6.0 | 60 |
| 5.05-6 | 27 | 6.0 | 60 |
| 6.05-7 | 32 | 8.0 | 75 |
| 7.05-8 | 36 | 8.0 | 75 |
| 8.1-9 | 41 | 10 | 85 |
| 9.1-10 | 45 | 10 | 85 |
| 10.1-11 | 50 | 12 | 95 |
| 11.1-12 | 54 | 12 | 95 |
| 12.1-12.5 | 57 | 14 | 100 |
| 12.6-13 | 59 | 14 | 100 |
| 13.5 | 61 | 14 | 105 |
| 14 | 63 | 14 | 105 |
| 14.5 | 65 | 16 | 110 |
| 15 | 68 | 16 | 110 |
| 15.5 | 70 | 16 | 120 |
| 16 | 72 | 16 | 120 |
| 16.5 | 75 | 16 | 125 |
| 17 | 77 | 16 | 125 |
| 17.5 | 79 | 16 | 130 |
| 18 | 81 | 16 | 130 |
| 18.5 | 84 | 16 | 135 |
| 19 | 86 | 16 | 135 |
| 19.5 | 88 | 16 | 145 |
| 20 | 90 | 20 | 145 |
特征 Features
■鎢鋼鉆頭采用瑞士HE涂層，針對每一支鉆頭都做了刃口C角鈍化處理，在抗崩的情況下充分降低鉆削阻力，獨特的橫刃設計讓斷削更為順暢，從而達到優異的鉆孔性能
| P | H | K | M | S | ||||||||||
| 碳素钢 | 合金钢 | 预硬钢 | 淬火钢钢 Hardened Steel | 铸铁 | 不锈钢铝合金铜合金 | N 塑胶 | 亚克力 高温合金钛合金 | |||||||
| Carbeon | AlloySteel | Prehardened | ~48HRC | ~55HRC | ~60HRC | ~65HRC | Cast Iron | Stainle | Aluminium | CAlpysr | Cemtint | Acrylic | ||
| O | O | |||||||||||||
單位UNIT=MM
| 刃径d1 | 避空长L1 | 柄径D | 总长L |
| 1-1.45 | 8.0 | 3.0 | 50 |
| 1.5-1.95 | 10 | 3.0 | 50 |
| 2-2.95 | 14 | 4.0 | 65 |
| 3-3.75 | 20 | 4.0 | 65 |
| 3.8-4 | 24 | 4.0 | 65 |
| 4.05-4.7 | 24 | 6.0 | 65 |
| 4.75-6 | 28 | 6.0 | 65 |
| 6.1-7 | 34 | 8.0 | |
| 7.1-8 | 41 | 8.0 | 80 |
| 8.1-10 | 47 | 10 | 80 |
| 10.1-12 | 55 | 12 | 90 |
| 12.5-14 | 60 | 14 | 100 110 |
| 14.5-16 | 65 | 16 | 115 |
注：3倍徑合金鉆頭訂貨號內冷為：JDA010X03S03C 非內冷為：JDA010X03S03N
| 规格 | 标准径 | 最级牙钻孔径最小 | |
| M1.0×0.2 | 0.8 | 0.821 | 0.783 |
| M1.1×0.2 | 0.9 | 0.921 | 0.883 |
| 1 | 0.983 | ||
| M1.2X0.2 | 1.021 | ||
| M1.4×0.2 | 1.2 | 1.221 | 1.183 |
| M1.6×0.2 | 1.4 | 1.421 | 1.383 |
| M1.7×0.2 | 1.45 | 1.5 | 1.46 |
| M1.8×0.2 | 1.6 | 1.621 | 1.583 |
| M2.0×0.25 | 1.75 | 1.785 | 1.729 |
| M2.2X0.25 | 1.95 | 1.985 | 1.929 |
| M2.3×0.25 | 2.05 | 2.061 | 2.001 |
| M2.5×0.35 | 2.2 | 2.221 | 2.121 |
| M2.6×0.35 | 2.2 | 2.246 | 2.186 |
| M3.0×0.35 | 2.7 | 2.721 | 2.621 |
| M3.5×0.35 | 3.2 | 3.221 | 3.121 |
| M4.0×0.5 | 3.5 | 3.599 | 3.459 |
| M4.5×0.5 | 4 | 4.099 | |
| 3.959 | |||
| M5.0×0.5 | 4.5 | 4.599 | 4.459 |
| M5.5×0.5 | 5 | 5.099 | 4.959 |
| M6.0×0.75 | 5.3 | 5.378 | 5.188 |
| M6.0×0.5 | 5.5 | 5.55 | 5.4 |
| M7.0X0.75 | 6.3 | 6.378 | 6.188 |
| M7.0×0.5 | 6.5 | 6.55 | 6.4 |
| M8.0X1.0 | 7.153 | 6.917 | |
| M8.0×0.75 | 7.3 | 7.378 | 7.188 |
| M8.0×0.5 | 7.5 | 7.52 | 7.4 |
| M9.0×1.0 | 8 | 8.153 | 7.917 |
| M9.0X0.75 | 8.3 | 8.378 | 8.188 |
| M10×1.25 | 8.8 | 8.912 | 8.647 |
| M10×1.0 | 9 | 9.153 | 8.917 |
| M10×0.75 | 9.3 | 9.378 | 9.188 |
| M10X0.5 | 9.5 | 9.52 | 9.4 |
| M11X1.0 | 10 | 10.153 | 9.917 |
| M11X0.75 | 10.3 | 10.378 | 10.188 |
| M12×1.5 | 10.5 | 10.676 | 10.376 |
| M12×1.25 | 10.8 | 10.912 | 10.647 |
| M12X1.0 | 11 | 11.153 | 10.917 |
| M12X0.5 | 11.5 | 11.52 | 11.4 |
| M14×1.5 | 12.5 13 | 12.676 | 12.376 |
| M14X1.0 | 13.5 | 13.153 | 12.917 |
| M15×1.5 | 14 | 13.676 14.153 | 13.376 |
| M15X1.0 | 14.5 | 14.676 | 13.917 |
| M16×1.5 | 15 | 15.153 | 14.376 14.917 |
| M16X1.0 | 15.5 | 15.676 | 15.376 |
| M17×1.5 | 16 | 16.153 | 15.917 |
| M17X1.0 | 16 | 16.21 | 15.835 |
| M18×2.0 | 16.5 | 16.676 | |
| M18X1.5 | 17 | 17.153 | 16.376 16.917 |
| M18×1.0 | 18 | 18.21 | 17.835 |
| M20×2.0 | 18.5 | 18.676 | 18.376 |
| M20×1.5 | 19 | 19.153 | 18.917 |
| M20×1.0 | 20 | 20.21 | |
| M22×2.0 | 20.5 | 20.676 | 19.835 |
| M22X1.5 | 20.376 | ||
| M22×1.0 | 21 22 | 21.153 | 20.917 |
| M24X2.0 | 22.21 | 21.835 | |
| M24X 1.5 | 22.5 | 22.676 | 22.376 |
| M24X1.0 | 23 | 23.153 | 22.917 |
| M25×2.0 | 23 | 23.21 | 22.835 |
| M25X1.5 | 23.5 | 23.676 | 23.376 |
| M25×1.0 | 24 | 24.153 | 23.917 |
| M26×1.5 | 24.5 | 24.676 | 24.376 |
| M27X2.0 | 25 25.5 | 25.21 | 24.835 |
| M27X1.5 | 25.676 | 25.376 | |
| M27×1.0 | 26 | 26.153 | 25.917 |
| M28×2.0 | 26 | 26.21 | 25.835 |
| 26.5 | 26.676 | 26.376 | |
| M28X1.5 | 27 | 27.153 | 26.917 |
| M28×1.0 | 27.252 | 26.752 | |
| M30X3.0 | 27 | ||
| M30×2.0 | 28 | 28.21 | 27.835 |
| M30X1.5 | 28.5 | 28.676 | 28.376 |
| M30X1.0 | 29 | 29.153 | 28.917 |
| M32X2.0 | 30 | 30.21 | 29.835 |
| 30.676 | 30.376 | ||
| M32X1.5 | 30.5 | ||
| M33X3.0 | 30 | 30.252 | 29.752 |
| M33×2.0 | 31 | 31.21 | 30.835 |
| M33×1.5 | 31.5 | 31.676 | 31.376 |
| M35X1.5 M36×3.0 | 33.5 33 | 33.676 33.252 | 33.376 32.752 |
| 英制PT管用螺纹 | ||||
| 规格 | 使用较刀时不用较刀时有效长 | 标准度 | ||
| PT1/16-28 | 6.10 | 6.20 | 6.244 | 6.384 |
| PT 1/8-28 | 8.10 | 8.20 | 8.249 | 8.388 |
| PT1/4-19 | 10.70 | 11.00 | 10.962 | 11.174 |
| PT3/8-19 | 14.20 | 14.50 | 14.448 | 14.658 |
| PT 1/2-14 | 17.60 | 18.00 | 17.979 | 18.263 |
| PT3/4-14 | 23.00 | 23.50 | 23.378 | 23.663 |
| PT1-11 | 29.00 | 29.50 | 29.459 | 29.822 |
| PT 1-1/4-11 | 37.50 | 38.00 | 37.976 | 38.339 |
| PT 1-1/2-11 | 43.40 | 44.00 | 43.869 | 44.232 |
| PT2-11 | 54.90 | 55.50 | 55.412 | 55.844 |
| 公制粗螺纹 标准径 | 最大级牙钻孔小 | ||
| M1.0×0.25 | 0.75 | 0.785 | 0.729 |
| M1.1×0.25 | 0.85 | 0.885 | 0.829 |
| M1.2×0.25 | 0.95 | 0.985 | 0.985 |
| M1.4×0.3 | 1.1 | 1.142 | 1.075 |
| M1.6×0.35 | 1.25 | 1.321 | 1.221 |
| M1.7×0.35 | 1.35 | 1.421 | 1.321 |
| M1.8×0.35 | 1.45 | 1.521 | 1.421 |
| M2.0×0.4 | 1.6 | 1.679 | 1.567 |
| M2.2×0.45 | 1.75 | 1.838 | 1.713 |
| M2.3×0.4 | 1.9 | 1.979 | 1.867 |
| M2.5×0.45 | 2.1 | 2.138 | 2.013 |
| M2.6×0.45 | 2.2 | 2.238 | 2.113 |
| M3.0×0.5 | 2.5 | 2.599 | 2.459 |
| M3.0×0.6 | 2.4 | 2.44 | 2.28 |
| M3.5×0.6 | 2.9 | 3.01 | 2.85 |
| M4.0×0.7 | 3.3 | 3.422 | 3.242 |
| M4.0×0.75 | 3.25 | 3.326 | 3.106 |
| M4.5×0.75 | 3.8 | 3.878 | 3.688 |
| M5.0×0.8 | 4.2 | 4.334 | 4.134 |
| M5.0×0.9 | 4.1 | 4.17 | 3.93 |
| M6.0×1.0 | 5 | 5.153 | 4.917 |
| M7.0×1.0 | 6 | 6.153 | 5.917 |
| M8.0×1.25 | 6.8 | 6.912 | 6.647 |
| M9.0×1.25 | 7.8 | 7.912 | 7.647 |
| M10×1.5 | 8.5 | 8.676 | 8.376 |
| M11×1.5 | 9.5 | 9.676 | 9.376 |
| M12×1.75 | 10.3 | 10.441 | 10.106 |
| M14X2.0 | 12 | 12.21 | 11.835 |
| M16×2.0 | 14 | 14.21 | 13.835 |
| M18×2.5 | 15.5 | 15.744 | 15.294 |
| M20×2.5 | 17.5 | 17.744 | 17.294 |
| M22×2.5 | 19.5 | 19.744 | 19.294 |
| M24×3.0 | 21 | 21.252 | 20.752 |
| M27×3.0 | 24 | 24.252 | 23.752 |
| M30×3.5 | 26.5 | 26.771 | 26.211 |
| 规格(UNC) | 标准径 | 2级牙钻孔径 | |
| 最大 | 最小 | ||
| NO.1-64(1.854) | 1.55 | 1.582 | 1.425 |
| NO.2-56(2.184) | 1.80 | 1.871 | 1.695 |
| NO.3-48(2.515) | 2.10 | 2.146 | 1.941 |
| NO.4-40(2.845) | 2.30 | 2.385 | 2.157 |
| NO.5-40(3.175) | 2.60 | 2.697 | 2.487 |
| NO.6-32(3.505) | 2.80 | 2.895 | 2.642 |
| NO.8-32(4.166) | 3.40 | 3.53 | 3.302 |
| NO.10-24(4.826) | 3.90 | 3.962 | 3.683 |
| NO.12-24(5.486) | 4.50 | 4.597 | 4.344 |
| 1/4-20 | 5.10 | 5.257 | 4.979 |
| 5/16-18 | 6.60 | 6.731 | 6.401 |
| 3/8-16 | 8.00 | 8.153 | 7.798 |
| 7/16-14 | 9.40 | 9.55 | 9.144 |
| 1/2-13 | 10.80 | 11.023 | 10.592 |
| 9/16-12 | 12.20 | 12.446 | 11.989 |
| 5/8-11 | 13.60 | 13.868 | 13.386 |
| 3/4-10 | 16.50 | 16.840 | 16.307 |
| 7/8-9 | 19.50 | 19.761 | 19.177 |
| 1 | 22.20 | 22.606 | 21.971 |
| 1-1/8-7 | 25.00 | 25.349 | 24.638 |
| 1-1/4-7 | 28.20 | 28.524 | 27.813 |
| 1-3/8-6 | 30.80 | 31.115 | 30.353 |
| 1-1/2-6 | 34.00 | 34.290 | 33.528 |
| 1-3/4-5 | 39.50 | 39.827 | 38.964 |
| 2-4-1/2 | 45.20 | 45.593 | 44.679 |
| 美制管螺纹 | |||
| 规格 | 钻孔径 | ||
| NPT | NPSC | ||
| 使用绞刀时不用绞刀时 | |||
| 1/16-27 | 5.94 | 6.15 | 6.35 |
| 1/8-27 | 8.33 | 8.43 | 8.74 |
| 1/4-18 | 10.72 | 11.13 | 11.13 |
| 3/8-18 | 14.27 | 14.27 | 14.68 |
| 1/2-18 | 17.48 | 17.86 | 18.26 |
| 3/4-14 | 22.63 | 23.01 | 23.42 |
| 1- 11-1/2 | 28.58 | 28.98 | 29.36 |
| 1-1/4-11-1/2 | 37.31 | 37.69 | 38.10 |
| 1-1/2-11-1/2 | 43.26 | 43.66 | 44.45 |
| 2 -11-1/2 | 55.17 | 55.58 | 56.36 |
| 美制特细螺纹 | |||
| 规格(UNEF) | 标准径 | 最大级牙钻孔小 | |
| NO.12-32 | 4.70 | 4.826 | 4.623 |
| 1/4-32 | 5.60 | 5.690 | 5.486 |
| 5/16-32 | 7.10 | 7.264 | 7.087 |
| 3/8-32 | 8.70 | 8.865 | 8.661 |
| 7/16-28 | 10.20 | 10.338 | 10.135 |
| 1/2-28 | 11.80 | 11.938 | 11.709 |
| 9/16-24 | 13.20 | 13.386 | 13.132 |
| 5/8-24 | 14.80 | 14.986 | 14.732 |
| 3/4-20 | 17.80 | 17.958 | 17.678 |
| 7/8-20 | 21.00 | 21.133 | 20.853 |
| 1-20 | 24.00 | 24.308 | 24.028 |
| 美制细螺纹 | |||
| 规格（UNF) | 标准径 | 2级牙钻孔径 | |
| 最大 | 最小 | ||
| NO.0-80(1.524) | 1.25 | 1.305 | 1.182 |
| NO.1-72(1.854) | 1.55 | 1.612 | 1.474 |
| NO.2-64(2.184) | 1.85 | 1.912 | 1.756 |
| NO.3-56(2.515) | 2.10 | 2.197 | 2.025 |
| NO.4-48(2.845) | 2.40 | 2.458 | 2.271 |
| NO.5-44(3.175) | 2.70 | 2.740 | 2.551 |
| NO.6-40(3.505) | 2.90 | 3.022 | 2.820 |
| NO.8-36(4.166) | 3.50 | 3.606 | 3.404 |
| NO.10-32（4.826) | 4.10 | 4.165 | 3.963 |
| NO.12-28(5.846) | 4.60 | 4.724 | 4.496 |
| 1/4-28 | 5.50 | 5.588 | 5.360 |
| 5/16-24 | 6.90 | 7.035 | 6.782 |
| 3/8-24 | 8.50 | 8.636 | 8.382 |
| 7/16-20 | 9.90 | 10.033 | 9.729 |
| 1/2-20 | 11.50 | 11.607 | 11.329 |
| 9/16-18 | 12.90 | 13.081 | 12.751 |
| 5/8-18 | 14.50 | 14.681 | 14.351 |
| 3/4-16 | 17.50 | 17.678 | 17.323 |
| 7/8-14 | 20.50 | 20.675 | 20.270 |
| 1-12 | 23.20 | 23.571 | 23.114 |
| 1-1/8-12 | 26.50 | 26.746 | 26.289 |
| 1-1/4-12 | 29.50 | 29.921 | 29.464 |
| 1-3/8-12 | 32.80 | 33.096 | 32.639 |
| 1-1/2-12 | 36.00 | 36.271 | 35.814 |
| 英制惠氏螺纹 | ||
| 规格 | 钻孔径 | |
| 硬材 | 软材 | |
| W1/8-40 | 2.65 | 2.6 |
| W5/32- 32 | 3.25 | 3.2 |
| W3/16-24 | 3.75 | 3.7 |
| W 1/4 - 20 | 5.1 | 5 |
| W5/16-18 | 6.6 | 6.5 |
| W3/8- 16 | 8 | 7.9 |
| W7/16-14 | 9.4 | 9.3 |
| W1/2 - 12 | 10.7 | 10.5 |
| W9/16-12 | 12.3 | 12 |
| W5/8 - 11 | 13.7 | 13.5 |
| W3/4-10 | 16.7 | 16.5 |
| W7/8-9 | 19.5 | 19.3 |
| W1-8 | 22.4 | 22 |
| W 1-1/8 - 7 | 25 | 24.8 |
| W1-1/4-7 | 28.3 | 28 |
| 美制管螺纹 | |||
| 规格 | 钻孔径 | ||
| NPSF | |||
| 使用绞刀时不用绞刀时 | |||
| 1/16-27 | 5.94 | 6.15 | 6.35 |
| 1/8 - 27 | 8.33 | 8.43 | 8.61 |
| 1/4-18 | 10.72 | 11.13 | 11.13 |
| 3/8 - 18 | 14.27 | 14.27 | 14.68 |
| 1/2-14 | 17.48 | 17.86 | 17.86 |
| 3/4 - 14 | 22.63 | 23.01 | 23.42 |
| 1-11-1/2 | 28.58 | 28.98 | 29.36 |
| 1-1/4-11-1/2 | 37.31 | 37.69 | |
| 1-1/2-11-1/2 | 43.26 | 43.66 | |
| 2 -11-1/2 | 55.17 | 55.58 | |
| 英制G牙管用螺纹 | |||
| 规格 | |||
| 底孔 | 标准 | 下限 | |
| G1/16-28 | 6.70 | 6.843 | 6.561 |
| G1/8-28 | 8.70 | 8.848 | 8.566 |
| G1/4-19 | 11.70 | 11.890 | 11.445 |
| G 3/8 - 19 | 15.20 | 15.395 | 14.950 |
| G1/2-14 | 19.00 | 19.172 | 18.631 |
| G 5/8 - 14 | 21.00 | 21.128 | 20.587 |
| G3/4-14 | 24.50 | 24.658 | 24.117 |
| G 7/8-14 | 28.20 | 28.418 | 27.877 |
| G1-11 | 30.60 | 30.931 | 30.291 |
| G1-1/8-11 | 35.20 | 35.579 | 34.939 |
| G 1-1/4- 11 | 39.20 | 39.592 | 38.952 |
| G 1-1/2 - 11 | 45.00 | 45.485 | 44.845 |
| G1-3/4-11 | 51.00 | 51.428 | 50.788 |
| G2-11 | 57.00 | 57.296 | 56.656 |
廣博機械工具（大連）有限公司
K&K Tools (dalian)Co., Ltd.
TEL:86-411-8857-5966http://www.jcinc.com.cn
